lcdwiki E32R40T LCD Touch Screen Display
Whakatakotoranga
- Product Name: LCDWIKI 4.0inch ESP32-32E E32R40T&E32N40T
- Whakaaturanga Whakaaturanga: 4.0inihi ESP32-32E
- Tau Tauira: CR2025-MI3275
- Webpae: www.lcdwiki.com
Te mana o te hua
Use the Type-C cable with power supply and data transmission function to connect the computer to the product and power the product. As shown in the picture below:
Tāutahia te taraiwa tauranga USB-ki-rangatū
- Locate the USB-SERIAL_CH340.zip package in the “7-工具软件_Tool_software” folder and decompress it.
- go to the folder after decompression, double-click “CH341SER.EXE” executable program, pop up the installation window, and then click “Install” button to continue the installation, as shown in the following picture:
After the installation is successful, click the window OK button to exit. Connect the computer USB to the development board and power on, and then enter the computer device manager, you can see that the CH340 port is identified under the port, as shown in the following picture:
Tahuna te ipu file
- Open the “Flash_Download” folder in “8-快速使用_Quick_Start”, locate the “flash_download_tool” folder, open the folder, and double-click the exe executable file o flash_download_tool. Ka rite ki te pikitia i raro nei:
- After opening the Flash download tool, ChipType select “ESP32”,WorkMode select “Develop”,LoadMode keep the default (UART), and then click “OK” button, as shown below:
Whakauruhia te atanga taputapu tango Flash, tuatahi tohua te ipu file to burn, bin file in the data package “8-快速使用_Quick_Start /bin” directory, as shown in the following figure:
- Patohia te paatene me nga ira e toru ki waenganui hei kowhiri i te ipu file i nga taahiraa o runga ake nei. I muri i te kowhiringa, tirohia te pouaka kei mua ka tautuhi i te wahitau e tahuna ana hei "0", penei i te pikitia e whai ake nei:
- Set SPI SPEED to “80MHz”, SPI MODE to “DIO”, and keep other Settings default, as shown in the following figure:
- Set COM, as long as the product is normally connected to the computer, COM port will be automatically recognized, click the drop-down menu to select. Set BAUD, click the drop-down menu to select, the larger the value, the faster the burning speed, but can not exceed the maximum transmission rate supported by the USB-to-serial chip. As shown in the picture below:
- Click the “START” button to enter the burning state. During the burning process, the status changes: “Waiting for synchronous power-on” -> “Downloading” -> “FINISH”, and the progress bar will also be loaded, as shown in the following picture:
Whakahaerehia te hotaka
I muri i te Bin file ka tahuna, pehia te paatene tautuhi o te hua, te mana ranei i runga i te hua, ka kite koe i te paanga o te mahi o te kaupapa, penei i te ahua i raro nei:
Pātai Auau
- Q: Me pehea taku mana ki te hua?
A: Use a Type-C cable with power supply and data transmission function to connect the computer to the product. - Q: How do I install the USB-to-Serial Port driver?
A: Locate and decompress the USB-SERIAL_CH340.zip package, then run CH341SER.EXE for installation. - Q: How do I burn the bin file?
A: Open the Flash_Download folder, run flash_download_tool, select ESP32 as ChipType, and follow the steps mentioned in the manual.
Tuhinga / Rauemi
 |
lcdwiki E32R40T LCD Touch Screen Display [pdf] Aratohu Kaiwhakamahi E32R40T, E32N40T, E32R40T LCD Touch Screen Display, E32R40T, LCD Touch Screen Display, Touch Screen Display, Screen Display, Display |