Lithonia Lighting T21 BL Track Lighting End Feed Connector Instruction Manual

Kupu Whakataki

This manual provides essential instructions for the safe installation and proper use of the Lithonia Lighting T21 BL Track Lighting End Feed Connector. This connector is specifically designed to supply power to Juno Lighting Trac-Master track systems.

The T21 BL connector is constructed from extruded aluminum with a thermoplastic insulator, ensuring both durability and reliable electrical performance within your lighting setup.

Nga korero haumaru

Please read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• WHAKATŪPATO: Te mate o te ru hiko. Momotuhia te hiko i te hiku, i te waahi ara iahiko ranei i mua i te whakauru, te mahi ranei.
• Ko nga hononga hiko katoa me rite ki nga ture a-rohe, ki nga tikanga, ki te Waehere Hiko Motu (NEC).
• Mena kāore koe i te mōhio ki ngā waea hiko, whakapā atu ki tētahi tohunga hiko.
• Do not install in wet locations or areas exposed to direct water spray. This product is intended for indoor use only.
• Me whakarite kia mau nga hononga katoa me te whakamaarama tika.

Ihirangi mokete

Verify that all components listed below are present and undamaged before proceeding with installation.

The image above displays the Lithonia Lighting T21 BL Track Lighting End Feed Connector and its associated components, including the main connector body, mounting bracket, threaded nipple, and lock nut.

• 1 x T21 BL End Feed Connector Body
• 1 x Mauri Maunga
• 1 x Threaded Nipple
• 1 x Lock Nut
• 1 x Ground Screw

Tatūnga me te Tāuta

Tuhinga o mua

• Turn off power at the circuit breaker or fuse box before starting any electrical work.
• Me whakarite he ma, he maroke, he pai te hanganga o te mata.
• Gather necessary tools: screwdriver, wire strippers, pliers, voltage Kaiwhakamatautau.

Nga Waahi Whakataunga

1. Prepare the Outlet Box: Ensure the electrical outlet box is properly installed and secured to the ceiling or wall.
2. Āpiti Taiapa Whakapuru: Secure the provided mounting bracket to the outlet box using appropriate screws (not included, typically supplied with the outlet box).
3. Tūhono Waea: Feed the electrical wires from the outlet box through the center hole of the mounting bracket and into the connector body. Connect the supply wires to the corresponding wires on the T21 BL connector (typically black to black, white to white, and ground to ground). Use approved wire connectors.
4. Secure Connector Body: Position the T21 BL connector body over the mounting bracket. Use the threaded nipple and lock nut to firmly secure the connector to the mounting bracket and outlet box.
5. Connect to Track System: Align the end feed connector with the end of your Juno Lighting Trac-Master track section. Slide the connector firmly into the track until it clicks into place, ensuring a secure electrical and mechanical connection.
6. Whakaora i te Mana: Once all connections are secure and the track system is fully assembled, restore power at the circuit breaker.

Tuhipoka: For optimal safety and performance, it is recommended that installation be performed by a qualified electrician.

Nga Tohutohu Whakahaere

The Lithonia Lighting T21 BL End Feed Connector is designed for continuous operation once properly installed. It serves as the power supply point for your track lighting system.

• Ensure all track heads or fixtures are correctly inserted and locked into the track system.
• Verify that the circuit breaker supplying power to the track is in the 'ON' position.
• If using a dimmer switch, ensure it is compatible with your track lighting fixtures and is functioning correctly.

Te tiaki

The T21 BL connector requires minimal maintenance to ensure long-lasting performance.

• Te horoi: Periodically wipe the exterior of the connector with a soft, dry cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
• Tirotiro: Annually inspect the connector and track system for any signs of damage, loose connections, or wear. If any issues are found, disconnect power and address them immediately.
• Do not attempt to disassemble or modify the connector. This will void the warranty and may create a safety hazard.

Raparongoā

If you experience issues with your track lighting system, refer to the following common troubleshooting steps:

• No Power to Track:
  • Check if the circuit breaker is tripped. Reset if necessary.
  • Ensure all wire connections at the outlet box and within the connector are secure.
  • Verify that the connector is fully seated and making proper contact with the track.
• Te Mana Waahi:
  • Inspect for loose connections within the connector or where the connector meets the track.
  • Check for any damage to the track or connector that might be causing poor contact.
• Nga Rarama Kapiki:
  • Ensure all track heads are properly installed and making good contact.
  • Manatokohia te tapeke wattage of your fixtures does not exceed the track system's capacity or the circuit's rating.

If troubleshooting steps do not resolve the issue, contact a qualified electrician or Lithonia Lighting customer support.

Whakatakotoranga

Pūtāhui

The Lithonia Lighting T21 BL Track Lighting End Feed Connector is backed by a 1 tau te whakamana a te kaiwhakanao mai i te ra o te hokonga. Ka kapi tenei raihana i nga hapa o nga rawa me nga mahi i raro i te whakamahinga me te ratonga.

Please retain your proof of purchase for warranty claims. The warranty does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.

Tautoko

For technical assistance, replacement parts, or to inquire about warranty claims, please contact Lithonia Lighting customer support. Refer to the official Lithonia Lighting webte waahi, te kohinga hua ranei mo nga korero whakapiri o naianei.

When contacting support, please have your product model number (T21 BL) and proof of purchase readily available.