Monoprice MS-01 Silver Speaker Stand Instruction Manual

Kupu Whakataki

The Monoprice MS-01 Silver Speaker Stand is designed to optimize the sound performance of your satellite speakers. Many small satellite speakers feature rear-firing ports to enhance bass response. For the best audio experience, it is recommended to position these speakers approximately 1-2 feet away from a wall, allowing the ports to function correctly. This floor stand set provides an ideal solution for placing your satellite speakers away from walls. The stands offer height adjustability from 26.8 inches to 43.3 inches, enabling you to position speakers at ear level when seated. Each stand can securely hold speakers weighing up to 5 lbs. Mounting options include a standard 1/4" x 20 mounting screw or a keyhole mount. Additionally, the stand tubes are hollow, facilitating discreet routing and concealment of speaker wires for a clean setup.

Ngā āhuatanga

• Allows speakers with rear-firing ports to breathe freely for optimal sound.
• Speaker height adjustable from 26.8" to 43.3" for customized listening levels.
• Supports up to 5 lbs weight per speaker.
• Mounts to speakers using standard 1/4" x 20 mounting screw or keyhole mount.
• Hollow stand tubes for integrated speaker wire management.

Huihuinga me te Whakanoho

Follow these steps to assemble and install your Monoprice MS-01 Speaker Stands:

1. Huihuinga turanga: Attach the main pole to the sturdy base. Ensure it is tightened securely to prevent wobbling.
2. Speaker Mounting Plate: Secure the speaker mounting plate to the top of the adjustable pole.
3. Āpitihanga Kaikōrero: Depending on your speaker type, use either the 1/4" x 20 mounting screw or the keyhole mount to attach your speaker to the plate. Ensure the speaker is firmly attached and stable.
4. Whakatikatika Teitei: Adjust the height of the stand to your desired listening level (between 26.8" and 43.3"). Lock the height adjustment mechanism firmly.
5. Whakaha Uepu: Route your speaker wires through the hollow tube of the stand for a clean and organized appearance. Ensure wires are not pinched.

Whakaahua 1: Te katoa view of the Monoprice MS-01 Speaker Stand with a speaker.

Figure 2: Detail of the speaker mounting plate, showing attachment points.

Figure 3: Close-up of the mounting bracket and height adjustment collar.

Nga Tohutohu Whakahaere

Once assembled and your speakers are securely mounted, the Monoprice MS-01 Speaker Stands require minimal operation. The primary operational aspect is adjusting the height to achieve your preferred listening experience. Ensure the height adjustment knob is fully tightened after any changes to maintain stability.

Te tiaki

• Te horoi: Wipe the stands with a soft, dry cloth to remove dust. Avoid abrasive cleaners or solvents that may damage the finish.
• Taki Pumau: Periodically check all screws and connections to ensure they remain tight. Re-tighten if necessary to maintain optimal stability.
• Tirohanga taura: Ensure speaker cables routed through the stand are not frayed or damaged. Replace any damaged cables immediately.

Raparongoā

• Ngā Tūnga Ruri: Ensure all assembly screws, especially those connecting the pole to the base and the mounting plate, are securely tightened. Verify the height adjustment knob is fully engaged.
• Speaker Not Fitting: Confirm your speaker's weight does not exceed 5 lbs. Check if your speaker has a 1/4" x 20 threaded hole or a keyhole slot for compatibility. If not, alternative mounting solutions may be required (not included).
• Cables Visible/Pinched: Re-route cables carefully through the hollow tube. Ensure no sharp edges are pressing against the cable insulation.

Whakatakotoranga

Pūtāhui me te Tautoko

Mo nga korero whakamana me te tautoko a nga kaihoko, tirohia te Monoprice mana webpaetukutuku, whakapā atu ranei ki ta raatau ratonga kaihoko. Puritia to riirii hoko mo etahi kereme whakamana.