Pukapuka Kaiwhakamahi mō te Pana Papa 3 Juniper EX2200-24T-4G

1. Kupu Whakataki

This manual provides essential information for the installation, operation, and maintenance of your Juniper EX2200-24T-4G Layer 3 Switch. The EX2200 series switches are designed to deliver high-performance, wire-rate forwarding capabilities, even with advanced control plane features enabled. This device incorporates an application-specific integrated circuit (ASIC)-based Packet Forwarding Engine (PFE) with an integrated CPU, ensuring consistent performance and reliability.

2. Hua Neke Atuview

The Juniper EX2200-24T-4G is a compact, high-performance Layer 3 Ethernet switch. It features 24 10/100/1000BASE-T Gigabit Ethernet ports for network connectivity and 4 Gigabit Ethernet SFP (Small Form-Factor Pluggable) uplink ports for fiber optic connections to other network devices or the core network.

Whakaahua 1: Front panel of the Juniper EX2200-24T-4G switch. This image displays the front panel of the Juniper EX2200-24T-4G switch. It features 24 RJ45 Gigabit Ethernet ports, numbered 0 through 23, arranged in two rows. To the right, there are four SFP (Small Form-Factor Pluggable) uplink ports, typically used for fiber optic connections. Status LEDs for system (SYS), alarm (ALM), speed (SPD), duplex (DX), enable (EN), and Power over Ethernet (POE) are also visible on the right side. Note that this specific model (EX2200-24T-4G) does not support PoE.

2.1 Nga waahanga matua

• 24 x 10/100/1000BASE-T Ethernet ports
• 4 x Gigabit Ethernet SFP uplink ports
• Layer 3 switching capabilities
• Junos operating system
• Hoahoa kiato 1U rack-mountable

3. Tatūnga

3.1 Te Wetewete

Carefully remove the switch and all accessories from the packaging. Verify that all components listed in the packing list are present. Retain the packaging materials for future use or transport.

3.2 Whakapiki

The EX2200-24T-4G switch can be deployed as a desktop unit or rack-mounted. For rack mounting, use the provided rack-mount kit and secure the switch in a standard 19-inch equipment rack. Ensure adequate airflow around the device for proper cooling.

3.3 Te Mana Hononga

1. Connect one end of the provided AC power cord to the AC power receptacle on the rear panel of the switch.
2. Connect the other end of the power cord to a grounded AC power outlet.
3. Ensure the power source provides the correct voltage (240 Volts).

3.4 Te Hononga Tauera Whatunga

• Tauranga RJ45: Connect standard Ethernet cables (Cat5e or higher) from your network devices (computers, servers, access points) to the 24 RJ45 ports on the front panel.
• SFP Uplink Ports: Insert compatible SFP transceivers into the 4 SFP uplink ports. Connect fiber optic cables from these transceivers to your core network or other switches.

3.5 Urunga Whirihoranga Tuatahi

To perform initial configuration, connect a console cable (RJ-45 to DB-9) from your management workstation to the console port on the switch. Use a terminal emulation program (e.g., PuTTY, Tera Term) with the following settings: 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control. Alternatively, if the switch has a default management IP, you can connect via a web browser or SSH after basic network connectivity is established.

4. Mahi

4.1 Hiko / Whakaweto

Once the power cord is connected, the switch will automatically power on. There is no separate power button. To power off, disconnect the power cord from the AC outlet.

4.2 Tohu LED

The front panel LEDs provide status information about the switch and its ports:

• SYS (Pūnaha): Indicates overall system status. Green for normal operation, amber for a fault.
• ALM (Alarm): Ka tohu i te ahua whakaoho.
• SPD (Speed): Indicates the link speed of the corresponding port.
• DX (Duplex): Indicates the duplex mode (half or full) of the corresponding port.
• EN (Enable): Indicates if the port is enabled.
• POE (Power over Ethernet): This LED is present but not functional on the EX2200-24T-4G model as it does not support PoE.

4.3 Junos OS

The switch runs on Juniper Networks' Junos operating system. Configuration and management are primarily performed via the command-line interface (CLI) accessible through the console port or SSH. Junos provides a robust and feature-rich environment for network management.

5. Tiaki

5.1 Te horoi

Keep the switch clean and free of dust. Use a soft, dry cloth to wipe the exterior. Do not use liquid or aerosol cleaners directly on the device. Ensure ventilation openings are clear of obstructions.

5.2 Whakahoutanga Firmware

Tirohia te tautoko a Juniper Networks i ia wā website for available Junos OS updates. Firmware updates can provide new features, performance enhancements, and security patches. Follow the instructions provided by Juniper Networks for the update process.

5.3 Nga Whakaaro Taiao

Operate the switch within its specified environmental limits (temperature, humidity). Ensure proper ventilation to prevent overheating. Avoid exposing the device to direct sunlight, excessive moisture, or extreme temperatures.

6. Te Raru

6.1 Karekau he Mana

• Verify the power cord is securely connected to both the switch and the AC outlet.
• Tirohia te putanga hiko me tetahi atu taputapu kia mohio kei te mahi.
• Me whakarite te puna hiko voltage matches the switch's requirements (240 Volts).

6.2 Kore he Hononga ki runga Tauranga

• Check the Ethernet cable for damage and ensure it is properly seated in both the switch port and the connected device.
• Manatokohia kei te noho te taputapu hono me te mahi tika.
• Check the port configuration in Junos OS to ensure it is enabled and correctly configured.
• For SFP ports, ensure the transceiver is correctly inserted and compatible, and the fiber optic cable is clean and undamaged.

6.3 System Alarm (ALM LED)

If the ALM LED is lit, consult the Junos OS documentation or the Juniper Networks support website for specific alarm codes and recommended actions. This typically indicates a hardware fault or a critical system event.

7. Whakatakotoranga

8. Tautoko me te Whaimana

8.1 Tautoko Hangarau

For technical assistance, documentation, and software downloads, please visit the official Juniper Networks support website. You can find resources such as knowledge base articles, community forums, and contact information for customer support.

8.2 Hua Whakatau

This Juniper Networks product is covered by a standard manufacturer's warranty. Details regarding the warranty period and terms can be found on the Juniper Networks official website or in the warranty documentation included with your purchase. Please retain your proof of purchase for warranty claims.