Kupu Whakataki
This manual provides comprehensive instructions for the installation, operation, and maintenance of your KEF CI130CR Round In-Ceiling Speaker. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.
The KEF CI130CR is a high-quality architectural loudspeaker designed for in-ceiling installation. It features an Ultra Thin Bezel design, a strong magnetic grille, an asymmetrical tweeter island for wide sound dispersion, a 0.75-inch aluminum dome tweeter with tangerine waveguide, and a 5.25-inch extended response bass driver.
Ihirangi mokete
- KEF CI130CR In-Ceiling Speaker (Single Unit)
- Roihi Aukume
- Pukapuka Tohutohu (tenei tuhinga)
- Mounting Template (if applicable, not explicitly mentioned but common)
Nga korero haumaru
- Me mohio kua momotuhia te hiko mai i te amphe whakakoi i mua i te hanga hononga.
- Consult a qualified electrician or installer if you are unsure about any part of the installation process.
- Kaua e whakaatuhia te kaikorero ki te makuku nui, ki ngā pāmahana tino kino rānei.
- Use appropriate safety gear (e.g., eye protection, gloves) during installation.
- Verify the structural integrity of the ceiling before cutting any holes.
Tatūnga me te Tāuta
1. Te Whakamahere i te Tūnga Kaikōrero
Consider the acoustics of the room and the desired sound coverage. For optimal stereo imaging, speakers should be equidistant from the primary listening position and spaced appropriately apart.
2. Preparing the Ceiling
- Locate ceiling joists to avoid cutting into them. Use a stud finder.
- Using the provided template (if available), mark the cutout area on the ceiling.
- Carefully cut the opening using a drywall saw or similar tool.
3. Waaho
Whakahaerehia te waea kaikorero mai i tō amplifier to the cutout location. Ensure the wire gauge is appropriate for the length of the run. Maintain correct polarity (+ to + and - to -) for all connections.
Whakaahua: Hoki view of the KEF CI130CR speaker. This image illustrates the gold-plated spring-loaded binding posts where speaker wires are connected, as well as the model number and manufacturer information.
- Strip approximately 1/2 inch (12mm) of insulation from the ends of the speaker wires.
- Press down on the spring-loaded binding posts on the back of the speaker.
- Insert the positive (+) wire (typically red or marked) into the red terminal and the negative (-) wire (typically black or unmarked) into the black terminal. Release the posts to secure the wires.
4. Te Whakamau i te Kaikōrero
Whakaahua: Taha view of the KEF CI130CR speaker. This image highlights the mounting clamps that secure the speaker to the ceiling.
Whakaahua: Taha taipitopito view of the KEF CI130CR speaker. This view provides a closer look at the internal structure and the robust mounting system.
- Carefully insert the speaker into the cutout hole.
- Tighten the mounting screws (usually located on the front baffle) evenly. This will cause the mounting clamps to pivot outwards and secure the speaker to the ceiling. Do not overtighten.
- Once secured, attach the magnetic grille to the front of the speaker. The grille will snap into place.
Nga Tohutohu Whakahaere
Once installed, connect your amplifier to a power source and turn it on. Begin playback at a low volume and gradually increase it to your desired listening level. The KEF CI130CR speakers are designed for wide sound dispersion, providing excellent audio quality across a broad listening area.
Whakaahua: Mua view of the KEF CI130CR speaker without its magnetic grille. This shows the 0.75-inch aluminum dome tweeter with tangerine waveguide and the 5.25-inch extended response bass driver.
Te Whakarite Oro
The CI130CR features an asymmetrical tweeter island. While no direct user adjustments are typically available on the speaker itself, sound characteristics can be fine-tuned through your amplifier's tone controls or room correction systems.
Te tiaki
- Te horoi: Dust the speaker grille gently with a soft, dry cloth. For stubborn marks, a slightly damp Ka taea te whakamahi i te kakahu, engari kia kore te makuku e uru ki roto i nga waahanga korero. Kaua e whakamahi i nga matū kino me nga horoi horoi.
- Te peita tunutunu: The magnetic grille is paintable. If you choose to paint it, ensure the paint is applied thinly and evenly to avoid clogging the perforations, which could affect sound quality. Remove the grille from the speaker before painting.
- Tirotiro: Tirohia te pūoro i ia wā, i ia wā, mō ngā tohu o te pakaru, o ngā hononga ngoikore rānei.
Raparongoā
| Raruraru | Take pea | Rongoā |
|---|---|---|
| Karekau he oro mai i te kaikorero |
|
|
| He oro parori ke ranei |
|
|
| Speaker grille not staying in place |
|
|
Whakatakotoranga
| Āhuahira | Taipitopito |
|---|---|
| Ingoa Tauira | CI130CR |
| Momo Kaikorero | Ki-Te Peehanga |
| Momo Whakaeke | Maunga Pouaka |
| Rahi Kaioro | 5.25 Inihi (Woofer) |
| Rahi Tweeter | 0.75 Inches (Aluminum Dome with Tangerine Waveguide) |
| Te aukati | 8 Ohm |
| Kaikorero Te Mana Putanga Morahi | 2 Watts (Note: This value seems unusually low for a speaker. It might refer to a specific test condition or be an error in the source data. Refer to KEF's official documentation for detailed power handling specifications.) |
| Rahi Hua (L x W x H) | 10 x 10 x 5.5 inihi |
| Taumaha Tūemi | 3.8 pauna |
| Tae | Mā |
| UPC | 637203207471 |
| Kaihanga | KEF |
Note: Specifications are subject to change without notice. For the most current information, please refer to the official KEF webpae, tuhinga hua ranei.
Pūtāhui me te Tautoko
For warranty information and technical support, please refer to the official KEF website or contact KEF customer service directly. Warranty terms and conditions may vary by region and retailer.
Note: The seller of this product has indicated "Sold as is no warranty or returns provided by seller." Any warranty claims or support requests should be directed to the manufacturer, KEF.
Mana o KEF Webpae: https://us.kef.com/
