Pukapuka Tohutohu mō te Reely Generation X 6S Korepara 1:8 RC Buggy

1. Kupu Whakataki

Thank you for choosing the Reely Generation X 6S Brushless 1:8 RC Buggy. This high-performance, four-wheel-drive (4WD) electric buggy is designed for enthusiasts seeking extreme speed and robust off-road capabilities. This manual provides essential information for the safe operation, setup, maintenance, and troubleshooting of your RC buggy.

Please read this manual thoroughly before operating the vehicle to ensure proper function and to prevent damage or injury. Keep this manual for future reference.

Whakatupato Haumaru

• Always operate the RC buggy in open areas, away from people, pets, and obstacles.
• Never operate near public roads or in residential areas where it could cause disturbance or danger.
• Tiakina nga ringa, nga makawe, me nga kakahu taratara mai i nga waahanga neke.
• Do not touch the motor or electronic speed controller (ESC) immediately after use, as they can become very hot.
• Ensure all batteries are charged safely and correctly. Use only compatible chargers and batteries.
• E taunakihia ana kia aroturukitia ngā kaiwhakahaere taitamariki e ngā pakeke.
• This product is not a toy and requires careful handling.

2. Ihirangi mokete

The Reely Generation X 6S Brushless 1:8 RC Buggy is supplied as a Ready-to-Run (RTR) package. Please verify that all components listed below are present in your box:

• Reely Generation X 6S Brushless 1:8 RC Buggy (fully assembled)
• 2.4 GHz Kaituku Mana Mamao
• Pukapuka Tohutohu (tenei tuhinga)

Note: Required batteries for both the vehicle and the remote control are not included and must be purchased separately.

Image: The Reely Generation X 6S Brushless 1:8 RC Buggy, showcasing its blue and black chassis with large off-road tires and a rear wing.

3. Tatūnga

3.1 Te Tāutanga Pūhiko (Waka)

1. Carefully remove the body clips and lift the buggy's body shell.
2. Locate the battery trays. The Generation X 6S is designed for 6S LiPo battery configurations (e.g., two 3S LiPo batteries in series, or one 6S LiPo battery). Ensure your batteries are fully charged and compatible with the XT90 connector system.
3. Securely place the batteries into the battery trays. Use the provided straps or Velcro to prevent movement during operation.
4. Connect the battery (or batteries) to the ESC using the XT90 connector. Ensure correct polarity.
5. Replace the body shell and secure it with the body clips.

3.2 Tāutanga Pūhiko (Mana Mamao)

Image: The 2.4 GHz remote control transmitter, featuring a steering wheel and trigger for throttle control.

1. Open the battery compartment cover on the bottom of the remote control.
2. Insert the required batteries (typically AA batteries, refer to the remote's specific markings) ensuring correct polarity (+/-).
3. Katia te uhi o te wahanga pākahiko.

3.3 Initial Checks and Binding

• Ensure the remote control is turned ON before turning on the vehicle.
• Whakakāhia te pana hiko o te waka (kei te nuinga o te wā kei te ESC).
• The vehicle and remote should automatically bind. If not, consult the remote control's specific instructions for binding procedures.
• Test steering and throttle response at a low speed to confirm proper function before full operation.

4. Mahi

4.1 Mana Taketake

• urungi: Use the steering wheel on the remote control to turn the front wheels left or right.
• Puta: Pull the trigger on the remote control to accelerate forward. Push the trigger forward to brake or reverse.

4.2 Tohutohu taraiwa

• Start with gentle throttle inputs, especially with the powerful 6S brushless system, to get accustomed to the vehicle's speed and handling.
• Practice steering and braking in an open area before attempting high-speed maneuvers.
• Avoid driving through deep water, as electronics, while water-resistant, are not fully submersible.
• Be mindful of battery life. Stop operating the vehicle when you notice a significant drop in power to prevent over-discharging LiPo batteries.

Image: The Reely Generation X 6S Buggy driving on a dirt surface, demonstrating its off-road capability.

5. Tiaki

5.1 I muri i ia Whakamahinga

• Disconnect and remove batteries from the vehicle and remote control.
• Clean the vehicle: Use a soft brush or compressed air to remove dirt, dust, and debris from the chassis, suspension, and drivetrain. A damp ka taea te whakamahi i te kakahu mo te anga tinana.
• Inspect for damage: Check for loose screws, bent suspension components, damaged tires, or any other signs of wear or breakage.

5.2 Tiaki i ia wa

• Whakahinuhinu: Apply appropriate RC-specific grease or oil to moving parts like universal joints and gears as needed. Avoid over-lubrication.
• Ngā Ārai Ru: Check for oil leaks and ensure smooth operation. Refill or replace shock oil if necessary.
• Tire me nga wira: Inspect for cracks, tears, or excessive wear. Ensure wheel nuts are tight.
• Hikohiko: Keep the motor, ESC, and servo clean and free of debris. Ensure all wiring connections are secure.

Whakaahua: He mua view of the Reely Generation X 6S Buggy, highlighting its robust suspension and front bumper.

6. Te Raru

For further assistance, please refer to the support section or contact your retailer.

7. Whakatakotoranga

8. Pūtāhui me te Tautoko

This Reely product comes with a minimum 2-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

Karekau te raihana e kapi i te kino i puta mai i:

• Te whakamahi kino, te mahi ranei.
• Accidents or collisions.
• Ko nga whakarereketanga kore mana, te whakatikatika ranei.
• Lack of proper maintenance.
• Ko te kakahu me te pakaru noa o nga waahanga ka pau.

For technical support, spare parts, or warranty inquiries, please contact your retailer or the Reely customer service department. Contact information can typically be found on the product packaging or the retailer's webpae.