Pukapuka Tohutohu mō te Pū Rehu Graco 17P484 HVLP EDGE II Plus

Kupu Whakataki

This manual provides essential information for the safe and effective use of your Graco 17P484 HVLP EDGE II Plus Spray Gun. This high-quality, professional-grade spray gun is designed for fine finishes, featuring an ergonomic, lightweight design with a 2-finger trigger. Please read all instructions carefully before operating the equipment.

Nga korero haumaru

WHAKATŪPATO: Ki te kore e whai i ēnei tohutohu haumaru, ka pāngia pea koe e te whara kino, e te kino rānei o ngā taonga.

• Always wear appropriate safety gear when handling pressurized liquids and chemicals. This includes eye protection, gloves, and respiratory protection as needed.
• Keep the sprayer away from heat sources and open flames.
• Kaua rawa e tohuhia te pu rehu ki te tangata, kararehe ranei.
• Ensure adequate ventilation when spraying, especially with solvent-based materials.
• After use, clean the sprayer thoroughly to remove any residual chemicals.
• Store the equipment in a cool, dry place, out of reach of children.
• Always follow the manufacturer's instructions for safe operation and maintenance of all components, including paints and solvents.

Nga waahanga hua me nga waahanga

The Graco 17P484 HVLP EDGE II Plus Spray Gun is designed for versatility and ease of use. Key features include:

• Adjustable Fluid Levels: A dedicated dial allows precise control over fluid output.
• Adjustable Fan Pattern: The fan pattern can be easily adjusted to suit various spraying applications.
• Quick Needle Swap: Designed for rapid and convenient needle changes, enhancing efficiency.
• Versatile Cup Compatibility: Can be used with a traditional 1 qt (0.95 L) metal cup or adapted for turbine pressure cups.
• Hoahoa Ergonomic: Lightweight with a 2-finger trigger for comfortable operation.
• Nga taputapu kei roto: Comes with a 1 qt (0.95 L) Metal Cup and a #3 Quick Release Fluid Set.

Whakaahua 1: The Graco 17P484 HVLP EDGE II Plus Spray Gun, shown with the attached 1-quart metal cup. This image highlights the gun's ergonomic handle, trigger, and the fluid and fan pattern adjustment points.

Tatūnga

1. Attach Fluid Cup: Securely attach the 1 qt (0.95 L) metal cup to the spray gun. Ensure it is tightened to prevent leaks. If using a turbine pressure cup, remove the standard fitting and attach the appropriate pressure cup fitting.
2. Hononga Pūtake Hau: Connect your air supply hose to the air inlet on the spray gun. The gun is designed for a maximum air pressure of 10 psi.
3. Fill with Material: Fill the fluid cup with the desired coating material (varnish, enamel, latex, stains). Ensure the material is properly thinned according to the coating manufacturer's recommendations for HVLP application.
4. Whakaritenga Tuatahi:
   • Taumata Wai: Use the dial on the gun to set the initial fluid level. Start with a lower setting and increase as needed.
   • Tauira Pā: Adjust the fan pattern by turning the air cap. This allows you to switch between horizontal, vertical, and round spray patterns.

Nga Tohutohu Whakahaere

1. Rehu Whakamatau: Before applying to your workpiece, perform a test spray on a scrap piece of material to verify the spray pattern and fluid output. Adjust the fluid level and fan pattern as necessary.
2. Pupuri Tawhiti: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches) for an even finish.
3. Nekehanga Totonu: Use smooth, overlapping passes. Release the trigger at the end of each pass to avoid excessive material buildup.
4. Trigger Control: The 2-finger trigger allows for comfortable and controlled application.

Te tiaki

Proper maintenance ensures the longevity and optimal performance of your spray gun.

• Te horoi i muri i te whakamahinga:
  • Ringihia te wai mai i te kapu, ringihia te toenga o ngā kai.
  • Fill the cup with an appropriate cleaning solvent (water for latex, mineral spirits for oil-based paints, etc.).
  • Rehuhia te whakarewa mā roto i te pū kia mārama ra ano.
  • Disassemble the air cap and fluid tip, cleaning them thoroughly with a brush and solvent.
  • Horoia te taha waho o te pū.
• Whakakapinga ngira: The needles can be swapped quickly. To replace, twist off the front section of the gun, push the release mechanism, and pull the needle out. Insert the new needle and reassemble. This process typically takes less than a minute.
• Rokiroki: Store the clean and dry spray gun in a safe place to prevent damage.

Raparongoā

If you encounter issues with your spray gun, consider the following common solutions:

• Poor Spray Pattern: Check for clogged fluid tip or air cap. Ensure material is properly thinned. Verify air pressure is adequate (max 10 psi).
• No Material Flow: Check if the fluid cup is empty or if the fluid tube is clogged. Ensure the fluid needle is not stuck.
• Nga turuturu: Inspect all connections for tightness. Check for damaged O-rings or seals and replace if necessary.
• Rehu Tauriterite: Ensure consistent air pressure. Check for blockages in the fluid path or air passages.

For persistent issues, contact Graco customer support or a certified service center.

Whakatakotoranga

Pūtāhui me te Tautoko

For warranty information, technical support, or to locate authorized service centers, please refer to the official Graco website or contact Graco customer service directly. Keep your purchase receipt for warranty claims.

Graco Official Webpae: www.graco.com