1. Kupu Whakataki
This manual provides essential information for the safe and effective operation of your Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ. This device is designed for precise measurement and analysis of electronic signals. Please read this manual thoroughly before using the instrument to ensure proper functionality and to prevent damage or injury.
2. Nga korero haumaru
Always observe the following safety precautions to prevent injury and avoid damage to this product or any products connected to it.
- Whakamahia te hua anake i tohua.
- Kaua e whakamahia te hua mena kua pakaru.
- Perform initial safety checks before connecting to power.
- Tirohia te ratonga ki nga kaimahi whai tohu.
- Me whakarite kia tika te hau kia kore e wera rawa.
- Kaua e mahi i te makuku, i te damp tikanga.
3. Tatūnga
Follow these steps to set up your oscilloscope for the first time:
- Unpack the Instrument: Carefully remove the oscilloscope and all accessories from the packaging. Inspect for any visible damage.
- Hono Hono: Connect the provided power cord to the AC input on the rear panel of the oscilloscope, then plug it into a grounded electrical outlet.
- Whakahiko: Press the power button, usually located on the front panel. The display should illuminate.
- Utu Whakamātautau: If using probes, connect a probe to Channel 1 and the probe compensation output. Adjust the probe compensation until a flat-top square wave is displayed.
This image serves as a placeholder and indicates that a specific product image is not available for display. It typically shows text like 'No image available' with a generic Amazon smile logo.
4. Nga Tohutohu Whakahaere
This section covers basic operation of the oscilloscope.
- Ngā Mana Poutū: Use the VOLTS/DIV knob to adjust the vertical scale (voltage per division) and the position knob to move the waveform vertically.
- Ngā Mana Whakapae: Use the SEC/DIV knob to adjust the horizontal scale (time per division) and the position knob to move the waveform horizontally.
- Pūnaha Keu: The trigger controls stabilize repetitive waveforms. Adjust the trigger level and mode (e.g., Edge, Pulse) to capture the desired part of the signal.
- Nga Mahi Ine: Access built-in measurement functions (e.g., Vpp, RMS, Frequency) via the 'Measure' or 'Menu' buttons.
5. Tiaki
Mā te tiaki tika ka roa te ora me te tika o tō oscilloscope.
- Te horoi: Horoia te taha o waho o te taputapu ki te ngohe, damp cloth. Do not use abrasive cleaners or solvents. Ensure the instrument is powered off and unplugged before cleaning.
- Whakatikatika: Regular calibration by qualified service personnel is recommended to maintain measurement accuracy. Refer to the service manual for calibration procedures.
- Rokiroki: When not in use, store the oscilloscope in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Te Raru
Ko tenei waahanga e whakarato ana i nga otinga mo nga take noa ka pa ki a koe.
| Raruraru | Take pea | Rongoā |
|---|---|---|
| Kaore he whakaaturanga i muri o te hiko | Power cord not connected; Power outlet fault; Internal fuse blown | Check power cord connection; Test power outlet; Contact service for fuse replacement |
| Kāore he āhua ngaru e whakaaturia ana | Input signal too small; Probe not connected; Trigger settings incorrect | Increase VOLTS/DIV; Check probe connection; Adjust trigger level and mode |
| Waveform unstable or rolling | Trigger level incorrect; Trigger source not selected; Input signal noisy | Adjust trigger level; Select correct trigger source; Use averaging mode for noisy signals |
7. Whakatakotoranga
Key technical specifications for the Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ.
| Whakatakotoranga | Uara |
|---|---|
| ASIN | B07GCZSDRJ |
| Kaihanga | Tektronix |
| Te Ra Tuatahi Wātea | Akuhata 11, 2018 |
8. Pūtāhui me te Tautoko
Tektronix products are designed for reliability and performance. This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Tektronix webpae.
For technical support, service, or to inquire about replacement parts, please contact Tektronix customer service. You can find contact information on the official Tektronix webte waahi, ma te tohatoha ranei o to rohe.
Tuhipoka: Ko nga whakatikatika, whakarereketanga kore ranei ka whakakorehia to raihana.
