Thermalright Aqua Elite 120 V3 Liquid CPU Cooler Instruction Manual

Ka mutu te huaview

The Thermalright Aqua Elite 120 V3 is an all-in-one liquid CPU cooler designed for efficient heat dissipation. It features a fourth-generation pump head, a 120mm aluminum fin heat sink, protective mesh water pipes, and a 120mm ARGB fan. This cooler is engineered for low vibration, high heat dissipation, and extended lifespan, providing optimal cooling performance for your CPU.

Image: Thermalright Aqua Elite 120 V3 ARGB All-in-one CPU Liquid Cooler components.

Ihirangi mokete

I mua i te tiimata o te whakaurunga, whakarite kei te noho nga waahanga katoa:

• Liquid CPU Cooler (Radiator, Pump, Fans, Tubing)
• Mounting hardware for AMD (AM4/AM5)
• Mounting hardware for Intel (LGA1150/1151/1155/1156/1200/2011/2066/1700)
• Taputapu Ngawha
• Pukapuka Kaiwhakamahi (tenei tuhinga)

Image: Close-up of the Thermalright Aqua Elite 120 V3 cooler highlighting ARGB lighting and design features.

Tatūnga me te Tāuta

Follow these steps carefully to install your Thermalright Aqua Elite 120 V3 Liquid CPU Cooler. Refer to the official installation video for visual guidance.

1. Prepare Motherboard

For AMD AM5 and AM4 motherboards: Remove the motherboard's plastic brackets around the CPU socket. Keep the original backplate as it will be reused.

For Intel LGA1700 motherboards: Use the outer mounting holes on the Intel backplate. Assemble the Intel backplate by using blue washers to fix the backplate screws. Install the assembled Intel backplate from the back side of the motherboard, ensuring backplate screws pass through the motherboard mounting holes. Install four blue standoffs onto the backplate screws. Install two Intel brackets onto the standoffs, aligning the LGA1700 holes on the brackets. Secure the brackets with nuts using a screwdriver.

Common Procedure: Apply thermal compound onto the CPU Integrated Heat Spreader (IHS). Remove the coldplate protective sticker from the waterblock. Place the waterblock onto the CPU, ensuring the waterblock bracket nuts align with the screws on the brackets. Tighten the nuts to secure the waterblock.

2. Tūhono Tauira

• Connect the fan PWM power cable to sync fan speed.
• Connect the fan ARGB cable to sync lighting signal.
• Connect the fan PWM power cable to the CPU_FAN socket on your motherboard.
• Connect the waterblock 4-pin PWM header to the motherboard's CPU_OPT or WATER_PUMP socket to power the water pump.
• Connect the ARGB lighting cable to a 3-pin 5V ARGB socket on your motherboard for lighting control.

Nga Tohutohu Whakahaere

The Thermalright Aqua Elite 120 V3 is designed for automatic operation once correctly installed and connected.

• Mana Pā PWM: The included TL-C12B-S V2 fan features PWM (Pulse Width Modulation) functionality, allowing it to automatically adjust its speed based on CPU temperature. This ensures optimal cooling performance while minimizing noise levels.
• ARGB Rama: The fan and pump head feature Addressable RGB (ARGB) lighting. If connected to a compatible 5V/3PIN ARGB motherboard header, the lighting can be controlled and synchronized using your motherboard's software. This allows for customization of lighting effects and colors.
• Efficient Pump Operation: The fourth-generation pump head operates at up to 3,300 RPM ± 10%, ensuring consistent and efficient coolant circulation for effective heat transfer away from the CPU.

Image: The octagonal water pump head with ARGB lighting and pump speed details.

Image: Details of the TL-C12B-S V2 fan, highlighting PWM control, S-FDB bearing, and shock-absorbing pads for quiet operation.

Te tiaki

Mā te tiaki auau ka roa te ora me te mahi tino pai o tō pouaka whakamatao CPU wai.

• Whakapai puehu: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Ensure the system is powered off before cleaning.
• Tirohanga ngongo: Inspect the water pipes for any signs of wear, kinks, or leaks. While the pipes are designed for low evaporation and high lifespan, regular checks are recommended.
• Pūhui Weariki: The thermal compound typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal compound.

Raparongoā

If you encounter issues with your Thermalright Aqua Elite 120 V3, refer to the following common troubleshooting tips:

• Te Paemahana PTM Teitei:
  • Ensure the waterblock is securely mounted to the CPU and thermal compound is properly applied.
  • Check if the fans are spinning correctly and not obstructed.
  • Verify that the pump is receiving power and operating (listen for a faint hum or feel for vibrations in the tubing).
  • Me whakarite kia pai te rere o te hau i roto i to keehi PC.
• Haruru nui:
  • Check fan blades for obstructions or loose mounting.
  • The S-FDB bearing in the fans is designed for low noise; however, ensure fan screws are tight.
  • Pump noise can occur if air is trapped in the loop. Gently tilt your PC case to help dislodge air bubbles.
• Ko te Rarama ARGB Kare e Mahi:
  • Verify that the ARGB cable is correctly connected to a 3-pin 5V ARGB header on your motherboard.
  • Tirohia te pūmanawa ARGB o tō papahoahoa kia mōhio ai kua whakahohea, kua whirihorahia hoki te rama.
  • Ensure the ARGB header on the motherboard is enabled in the BIOS/UEFI settings if applicable.
• Pump Not Functioning:
  • Confirm the 4-pin PWM header from the waterblock is securely connected to the CPU_OPT or WATER_PUMP header on the motherboard.
  • Check motherboard BIOS/UEFI settings to ensure the pump header is configured correctly and receiving power.

Whakatakotoranga

Pūtāhui me te Tautoko

He mea hanga ngā hua Thermalright ki ngā paerewa kounga teitei. Mō ngā mōhiohio pūtāhui, tautoko hangarau, pātai ratonga rānei, tirohia te tari mana o Thermalright. webpaetukutuku, whakapā atu ranei ki ta raatau tautoko kaihoko. Puritia to rihiti hoko mo nga kereme whakamana.