Kupu Whakataki
Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.
Nga Korero Haumaru Nui
Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.
- Verify that your monitor's weight and VESA pattern are within the specified limits.
- Do not exceed the maximum load capacity of 26.5 lbs per arm.
- Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
- Use only the provided hardware.
- Tiakina nga waahanga iti mai i nga tamariki.
Whakatakotoranga
- Tauira: EGCM13B
- Hototahitanga Rahi Mata: 13 ki te 34 inihi
- Weight Capacity (per arm): Tae atu ki te 26.5 lbs
- Hototahitanga VESA: 75x75 mm, 100x100 mm
- Arm Span: 33 inihi
- Teitei Pou: 16.3 inihi
- Momo Nekehanga: Tilt, Swivel, Rotation, Articulating
- Koki Honga Morahi: 90 Waeine
- Rauemi: Korotahi Steel
- Tae: Pango
- Momo Whakapuru: Maunga Papa (C-Cl)amp rānei Grommet)
- C-Clamp Te Matotoru Papa: 0.39" - 3.15"
- Grommet Mount Desk Thickness: 0.39" - 2.17"
- Grommet Hole Diameter: 0.47" - 0.79"
Ihirangi mokete
Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.
- Pou Matua me te Papamahiamp/Turanga Grommet
- Taarua Aroturuki Arms
- Pereti VESA (2x)
- Mounting Hardware (screws, washers, tools)
- Topenga Whakahaere Taura
- Pukapuka Tohutohu
Tatūnga me te Tāuta
1. Tirotiro Hototahi ki te Papamahi
Before installation, ensure your desk meets the following criteria:
- Rauemi: Recommended for wooden tables.
- Raro: Preferably free of beams or panels that may interfere with installation.
- C-Clamp Mātotoru: 0.39" - 3.15"
- Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")
2. Monitor Compatibility Check
Each monitor must meet these conditions:
- Rahi Mata: 13 ki te 34 inihi
- Taumaha: Tae atu ki te 26.5 lbs
- VESA Whakapuru Kohao: 75x75 mm or 100x100 mm apart on the back of the monitor.
3. Assemble the Pole with Clamp Tautoko
Choose either C-Clamp or Grommet installation based on your desk type.
Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.
4. Assemble the Arm and Pole Wire Clips
Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.
5. Assemble VESA Plate and Monitor
Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.
6. Install the Monitor to the Swivel Arm
Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).
Te Whakahaere me ngā Whakarerekētanga
The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewte whakamarie:
- Whakatikatika Teitei: Wewetehia te clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp haumaru.
- Tapahia: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
- Hurihuri: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewmai i nga kokonga rereke.
- Hurihuri: Hurihia te aroturuki 360 nga nekehanga ki te huri i waenga i nga whakatakotoranga whenua me nga whakaahua.
- Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.
Te tiaki
- Takitaki ia ia nga wa katoa nga wiri me nga hononga kia mau tonu, kia mau.
- Horoia te maunga ki te wai ngohengohe,amp kakahu. A ape i nga kai horoi abrasive.
- Do not disassemble the mount unless instructed to do so.
Raparongoā
- Kāore ngā aroturuki i te papatahi: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
- Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
- Kāore i te pumau te āhua o te maunga: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.
Pūtāhui me te Tautoko
For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.
