BLANCO 443276 Digital Water Filter Flow Meter User Manual

1. Hua Neke Atuview

The BLANCO 443276 Digital Water Filter Flow Meter is designed to accurately track your filtered water usage, providing a clear indication of when your water filter requires replacement. This precision helps optimize filter lifespan and prevents unnecessary filter changes, contributing to cost savings. It is compatible with BLANCO filter starter kits and filter-ready faucets, integrating seamlessly into your water filtration system.

Figure 1: The BLANCO 443276 Digital Water Filter Flow Meter, showing the digital display unit and the separate flow sensor connected by a cable.

2. He aha kei roto i te Pouaka

• Digital Filter Flow Meter (Display Unit and Flow Sensor)

3. Nga waahanga matua

• Compatible with BLANCO Filter Start Sets.
• Designed for filter replacement every six months or after 400 gallons, whichever comes first.
• Provides an accurate reading of filtered water usage.
• Displays the amount of water being processed through the filter.
• Display easily resets for the next cycle once the filter is replaced.

4. Whakatakotoranga

5. Tatūnga me te Tāuta

5.1 Whakatupato Haumaru

• Me whakarite kia whakawetohia te puna wai matua i mua i te tīmatanga o te tāutanga.
• Use appropriate tools and follow all local plumbing codes.
• Do not overtighten connections to prevent damage to the flow sensor or plumbing.

5.2 Nga Waahi Whakataunga

1. Tāutuhia te Pūwāhi Tāutanga: The flow meter should be installed on the cold water line leading to your water filter system, typically under the sink. Ensure there is sufficient space for the flow sensor and the display unit.
2. Whakawetohia te Wai: Locate the main water shut-off valve for your home or the specific cold water line under the sink and turn it off. Open a nearby faucet to relieve pressure.
3. Tapahia te Raina Wai: Carefully cut the cold water line at the desired installation point. Ensure clean, straight cuts for proper sealing.
4. Tāutahia te Pūoko Rere: Insert the flow sensor into the cut water line, ensuring the flow direction arrow on the sensor matches the direction of water flow. Use appropriate fittings (not included, typically part of a filter starter kit) to connect the sensor securely.
5. Honoa te Wāhanga Whakaaturanga: Connect the cable from the flow sensor to the display unit. Ensure the connection is secure.
6. Whakamau i te Wāhanga Whakaaturanga: Mount the display unit in a convenient and accessible location, such as inside the cabinet under the sink, using screws or adhesive (not included).
7. Whakahokia te Waiwai: Slowly turn the main water supply back on. Check all connections for leaks.
8. Hinga-Whakaoho tuatahi: The display unit should power on automatically once water flows through the sensor, or it may require battery installation (see section 5.3).

5.3 Battery Installation (if applicable)

While some units are powered by water flow, others may require batteries. If your display unit does not power on, locate the battery compartment (usually on the back or side of the display unit), insert the required batteries (e.g., 2x AAA, not included) according to polarity markings, and close the compartment.

6. Nga Tohutohu Whakahaere

6.1 Te Maramatanga ki te Whakaaturanga

The digital display shows the total volume of water that has passed through the filter since the last reset. The unit of measurement (e.g., gallons or liters) may be indicated on the display or in the product packaging.

Figure 2: A user holding the BLANCO 443276 Digital Water Filter Flow Meter display unit, showing the digital screen and control buttons.

6.2 Resetting the Flow Meter

After replacing your water filter, it is crucial to reset the flow meter to accurately track the usage of the new filter. To reset:

1. Locate the "DISPLAY/RESET" button on the front of the display unit.
2. Press and hold the "DISPLAY/RESET" button for approximately 3-5 seconds until the display shows "00" or resets to zero.
3. Release the button. The meter is now ready to track the usage of your new filter.

6.3 Monitoring Filter Life

The BLANCO 443276 is designed to help you replace your filter every six months or after 400 gallons, whichever comes first. Regularly check the display to monitor the accumulated water volume. When the reading approaches 400 gallons or six months have passed since the last filter replacement, it is time to change your filter.

7. Tiaki

7.1 Tātari Whakakapinga

Refer to your water filter's specific instructions for proper replacement procedures. After replacing the filter, always reset the BLANCO 443276 Digital Water Filter Flow Meter as described in Section 6.2.

7.2 Te horoi

Horoia te wae whakaatu ki te ngohe, damp kakahu. Kaua e whakamahi i nga kai horoi, i nga whakarewa ranei, na te mea ka kino te whakaaturanga, casing.

7.3 Battery Replacement (if applicable)

If the display becomes dim or unresponsive, it may be time to replace the batteries. Follow the steps in Section 5.3 to replace the batteries. Ensure proper disposal of old batteries according to local regulations.

8. Te Raru

9. Pūtāhui me te Tautoko

For warranty information, technical support, or to purchase replacement parts, please contact BLANCO customer service. You can typically find contact details on the official BLANCO webpae, na roto ranei i nga tuhinga hoko a to hua.

BLANCO Official Webpae: www.blancoamerica.com