Emomo 8 Pin Massage Remote Control Handset User Manual

1. Kupu Whakataki

This manual provides essential instructions for the proper installation, operation, and maintenance of your Emomo 8 Pin Massage Remote Control Handset, models NHX03 and NHX034. This remote is designed for use with various brands of heat and massage power recliner lift chairs. Please read this manual thoroughly before use to ensure correct functionality and to prevent damage.

2. Hua Neke Atuview

The Emomo 8 Pin Massage Remote Control Handset features a display and multiple buttons for controlling massage, heat, and reclining functions of compatible chairs. It is crucial to verify the model number and connector type for proper compatibility.

Figure 2.1: Emomo 8 Pin Massage Remote Control Handset with its connecting cable.

Whakaahua 2.2: Whakatata view of the remote control's display and function buttons.

3. Tirohanga Hototahi

Before attempting to replace your existing remote, it is essential to confirm compatibility. This remote is specifically designed for Emomo 8 male pin massage systems, models NHX03 and NHX034. There are several versions of these models with varying functions and buttons.

3.1 Model and Serial Number Verification

Locate the barcode sticker on the back of your existing remote. The serial number is typically found below this barcode. Ensure that the model number (NHX03 or NHX034) and the serial number match your current remote for proper replacement. This remote will not fit model NHX032.

Figure 3.1: Back of the remote control displaying the model and serial number sticker. The serial number is E034KD8HL245BP2000708A01974.

3.2 Connector Type Verification

This remote features an 8-male pin connection designed to plug into the control box of your recliner. Verify that your chair's control box has a compatible 8-pin female port. If the pin configuration or number of pins differs, this remote cannot be used as a replacement.

Whakaahua 3.2: Whakatata view of the 8-pin male connector, which must match the chair's female port.

4. Tatūnga

1. Momotu Hiko: Before connecting the new remote, ensure your power recliner lift chair is completely disconnected from its power source. Unplug the chair from the wall outlet.
2. Kimihia te Pouaka Mana: Identify the control box on your recliner, typically located underneath the chair or near the motor.
3. Tūhono Mamao: Carefully align the 8-male pin connector of the new remote with the corresponding 8-female pin port on the chair's control box. Push firmly until the connection is secure. Do not force the connector.
4. Honoa Anō te Mana: Once the remote is securely connected, plug your recliner back into the wall outlet.
5. Taumahinga Whakamatau: Test all buttons on the remote to ensure proper operation of the chair's functions.

5. Nga Tohutohu Whakahaere

The Emomo remote control provides intuitive access to your recliner's features. Button functions may vary slightly depending on the specific version of your NHX03/NHX034 remote and the chair's capabilities.

• KIA/WATA: Powers the massage and heat functions on or off.
• Runga / Raro: Controls the reclining and lifting mechanisms of the chair. Press and hold to adjust the chair's position.
• KAUPAPA: Adjusts the strength or intensity level of the massage function.
• MOTO: Activates a pre-programmed automatic massage sequence.
• AHUNGA: Cycles through different massage modes or patterns.
• WAHI: Targets specific massage zones or points on the body.
• TAIMA: Sets a duration for the massage or heat functions, typically in increments (e.g., 10, 20, 30 minutes).
• TE wera: Activates or deactivates the heating function in the chair.

6. Tiaki

• Te horoi: Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners, abrasive materials, or solvents, as these can damage the display and buttons.
• Rokiroki: When not in use, store the remote in a safe place where it will not be dropped or exposed to extreme temperatures or moisture.
• Tiaki taura: Avoid bending or twisting the cable excessively, as this can damage the internal wires and connections.
• Mana: This remote operates using the chair's power supply. No batteries are required for the remote itself.

7. Te Raru

If you encounter issues with your Emomo remote control, refer to the following common troubleshooting steps:

• Mamao Kaore i te Whakautu:
  • Ensure the chair is properly plugged into a working power outlet.
  • Check that the 8-pin connector is securely plugged into the chair's control box. Disconnect and reconnect to ensure a firm connection.
  • Verify that the chair's main power switch (if applicable) is in the 'ON' position.
• Whakaatu Kaore i te Mahi:
  • Confirm power supply to the chair.
  • Check for any visible damage to the remote or cable.
• Specific Function Not Working (e.g., Heat, Massage):
  • Ensure the function is activated via the remote's button.
  • Some chairs may have a master control or safety feature that needs to be engaged.
• Incompatible Remote:
  • If the remote was recently replaced, double-check the model number and 8-pin connector type against your original remote and chair specifications as detailed in Section 3. An incorrect remote will not function.

If problems persist after attempting these steps, consult a qualified technician or contact the product's support for further assistance.

8. Whakatakotoranga

9. Pūtāhui me te Tautoko

For warranty information or technical support, please refer to the documentation provided with your power recliner lift chair or contact the manufacturer of the chair. For issues specifically related to the Emomo remote control, please contact the seller or Emomo customer service directly. Ensure you have your product model and serial number ready when seeking support.