AstroAI L8 Portable Electric Bike Pump

1. Nga korero haumaru

Please read all safety instructions carefully before using the AstroAI L8 Portable Electric Bike Pump. Failure to follow these instructions may result in injury or damage to the device.

• Tiakina te taputapu mai i nga tamariki.
• Do not expose the pump to extreme temperatures or direct sunlight for prolonged periods.
• Avoid using the pump in wet conditions or near flammable liquids/gases.
• Ensure the correct pressure is set for the item being inflated to prevent over-inflation, which can cause bursting and injury.
• Do not operate the pump continuously for more than 12 minutes. Allow it to cool down for at least 15 minutes after continuous use.
• This pump is not suitable for inflating car tires, Segways, or electric scooters.

2. Ihirangi mokete

Manatokona kei roto katoa nga mea kei roto i te kete:

• 1 x AstroAI Electric Bike Pump
• 1 x Schrader Hose
• 1 x Presta Valve Whāurutau
• 1 x Dunlop Valve Adapter
• 1 x Poi Neira
• 1 x Momo-C Uira Kaiha
• 1 x Puke Rokiroki
• 1 x Pukapuka Kaiwhakamahi

3. Hua Neke Atuview

The AstroAI L8 Portable Electric Bike Pump is a compact and versatile tire inflator designed for various bicycles, e-bikes, motorcycles, and sports balls. It features a digital display, preset modes, and an auto-shutoff function for precise inflation.

Figure 3.1: AstroAI L8 Portable Bike Pump with included valve adapters.

The pump is equipped with a high-voltage motor for efficient inflation, capable of inflating a 700 x 35C city bike tire from 60 PSI to 80 PSI in approximately 35 seconds. Its lightweight and ergonomic design make it easy to carry and store.

Figure 3.2: Compact and portable design of the AstroAI L8 pump.

Whakaatu me nga Mana

Figure 3.3: Dual-value LED display and control buttons.

The LED display shows both real-time and preset pressure values. Control buttons allow for mode selection, unit switching (PSI/BAR), and pressure adjustment.

4. Ka tohatohahia te Pūrere

The AstroAI L8 pump is equipped with a built-in lithium battery and supports Type-C charging. Before first use, fully charge the device.

1. Connect the provided Type-C charging cable to the pump's charging port.
2. Honoa te pito o te taura ki tētahi urutau hiko USB e tika ana (kāore i roto).
3. The battery indicator on the display will show charging status. Once fully charged, the indicator will show a full battery.

A single full charge can inflate up to 25 city bike tires (60–80 PSI).

5. Setup and Valve Adapters

The pump comes with a Schrader valve hose and adapters for Presta and Dunlop valves.

Attaching the Schrader Hose

1. Screw the Schrader hose securely onto the pump's air outlet.
2. For Schrader valves, directly connect the hose to the tire valve.

Using Presta and Dunlop Valve Adapters

For Presta or Dunlop valves, first install the appropriate adapter onto the tire valve, then connect the Schrader hose to the adapter.

• Takirere Presta: Unscrew the Presta valve cap, then screw on the Presta valve adapter.
• Dunlop Valve: Screw on the Dunlop valve adapter.

Figure 5.1: Included valve adapters for versatile use.

6. Mahi

Te Hiko / Whakaweto

• To turn on: Press and hold the Power Button for 3 seconds.
• To turn off: Press and hold the Power Button for 3 seconds, or the device will automatically shut off after a period of inactivity.

Kōwhiringa Aratau

The pump offers 5 preset modes and a custom mode. Press the 'M' button to cycle through the modes:

• Paihikara Taone
• Paihikara Maunga
• Paihikara Huarahi
• Paihikara Ngako
• Custom Mode (for motorcycles, balls, etc.)

Figure 6.1: Available preset and custom inflation modes.

Setting Pressure and Inflation

1. After selecting a mode, use the '+' and '-' buttons to adjust the desired pressure.
2. Press the unit button to switch between PSI and BAR units.
3. Connect the hose to the tire valve (with adapter if necessary).
4. Press the Power Button to start inflation. The pump will display real-time pressure.
5. Ka mutu aunoa te papu ina tae ki te pēhanga kua whakaritea.

Figure 6.2: Setting preset pressure and automatic shutoff feature.

The memory function saves your last pressure setting for convenience.

7. Rama Rama

The AstroAI L8 pump includes a built-in LED light with three modes for enhanced visibility and safety:

• Maama Tonu: Mō te whakamārama whānui.
• Rama Tere: For signaling or increased visibility.
• Fast Flash (SOS): For emergency situations.

To activate or change modes, press the flashlight button.

Figure 7.1: LED flashlight with three modes.

8. Tiaki

• Clean the pump exterior with a soft, damp kakahu. Kaua e whakamahi i nga matū kino me nga horoi horoi.
• Whakaorangia te papu ki te waahi makariri, maroke ina kore e whakamahia.
• Me whakarite kia noho kore he puehu me te otaota te tauranga utu.
• Regularly check the hose and adapters for any signs of wear or damage. Replace if necessary.

9. Te Raru

10. Whakatakotoranga

11. Pūtāhui me te Tautoko

The AstroAI L8 Portable Electric Bike Pump comes with a 2-Tau Whakaputanga Kaihanga.

For technical support, warranty claims, or any questions regarding your product, please contact AstroAI customer service through their official webpae, nga korero whakapā ranei e whakaratohia ana i roto i to tuhinga hoko.

12. Hua Ataata