DuraTherm Digital Heating Huānga Kaiwhakahaere Tohutohu Manual
KAUPAPA KAUPAPA KAUPAPA HIKO
Tena koa panuihia nga tohutohu i mua i te ngana ki te tarai i te hua, ki te taapiri ranei ki to punaha hiko.
Tena koa kia whiriwhiria e koe he huānga hiko e tika ana mo to whakamahana tauera.
Whakatupatotanga Haumaru: Me Whakatauhia tenei hua e tetahi tangata mohio ka taea e ia te whakarite kia rite ki te IEE. Wāhanga P me ngā ture whakahaere ā-rohe. Me whakarite kia wehea te ara iahiko hiko matua me te wae whakakorikori i mua i te whakawiri. Kaua tenei wae e whakauru ki te Rohe kaukau IEE.1.
NGĀ TOHUTOHU WIRINGA
Kei te hiahiatia he spur hono i roto i te ara iahiko tuku ki te kaiwhakahaere. kua whakauruhia ki te rahinga tika.
Ko nga pito 2 x E & 2 x N e hono ana ki te papa iahiko kua taia.
NGĀ WAERE HUARANGA HIKO (WAwaho) |
Mai i te Maui ki te Matau ko nga pito 1-3 e hono ana ki te taura Huanga Me hono nga waea huānga penei: Whenua Kakariki/Kowhai to terminal 1 (N on board) Kahurangi kūpapa to terminal 2 (L on board) Ora Parauri to terminal 3 (L/T on board) TINO NUI - Me whenua tenei wae |
WAea UERA MAIN (IN) |
From Left to Right terminals 4-6 correspond to the Mains cable wires Me hono nga waea taura matua e whai ake nei: Ora Parauri to terminal 4 (L on board) Kahurangi kūpapa to terminal 5 (N on board) Whenua Kakariki/Kowhai to terminal 6 (E on board) VERY IMPORIANT – Me whenua tenei wae |
 |
Clamp te taura huānga ki raro o te pūmana taiepa |
| Whakanohoia te pereti mana ki te pouaka o muri kia kore ai e mau nga waea i te wa e noho ana. Whakamahia nga wiri whakatika e rua hei mau ki te pouaka o muri. |  |
NGA TOHUTOHU WHAKAMAHI
There are four buttons on the control plate. ON/OFF (1), temperature Increase (2), heke te pāmahana (3), ECO boost button (4).
WHAKAMAHI KAUPAPA
The unit in standby has the main LED in Whero. To turn on in normal mode, press the ON/OFF pātene me
release it. The LED ka huri KURU, te LED ORANGE bank will light between one to five LED o.
To increase or decrease the temperature press the ‘increase/decrease’ buttons to attain the desired setting. Each one of the ORANGE LEDs represents the following power output from the element:
5 LEDs =100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% power
Hei huri i te waeine WATE. pehia te ON/OFF pātene ka tuku.
NB The control plate contains a memory and whatever the temperature that was set when the unit was turned Whakaweto, will be the temperature (number of LED’s lit) that the element will resume at when the unit is turned ON te wa e whai ake nei.
MAHI ECO
Press the ECU button from either power on or from standard control. the power LED will turn GREEN. The
ECO function allows you to go to a higher power setting for 30 minutes (To heat the towel warmer) this power level can be set in the first 30 minutes. After 30 minutes the power is reduced to the pre-set lower level for 90 minutes. The power output can be set using the increase/ decrease buttons to set your preferred rail temperature. After 2 Hours the controller will turn on.
Both the 30 minute and the 90 minutes settings are saved in the controller.
5 LEDs = 100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% mana
Raraunga Hangarau.
Parenga urunga: IPX4
Voltage: 230-245 waatea
Putanga mana teitei: 800w
Ahu: 85 x 85 x 20mm
Whakaaetanga: CE, tested to EN55014-1:2006
Tuhinga / Rauemi
 |
DuraTherm Digital Heating Element Controller [pdf] Pukapuka Tohutohu Kaiwhakahaere Huānga Whakawera Mamati, Kaiwhakahaere Huānga Whakawera, Kaiwhakahaere Huānga, Kaiwhakahaere |