EDA Technology ED-HMI2002-070C Industrial Automation and Control User Manual
Īmēra: sales@edatec.cn / support@edatec.cn
Web: www.edatec.cn
Waea: +86-15921483028(Haina) | +86-18217351262(Tawahi)
1 Pukapuka Pumau
Ko tenei upoko e whakaatu ana i te huaview, rarangi whakakakahu, ahua, tohu me te atanga.
1.1 Neke atuview
Ko te ED-HMI2002-070C he HMI ahumahi 7-inihi i runga i te Raspberry Pi 4. E ai ki nga ahuatanga tono rereke me nga hiahia o te kaiwhakamahi, ka taea te whiriwhiri i nga waahanga rereke o te RAM me nga rorohiko rorohiko kaari SD.
- RAM can choose 1GB, 2GB, 4GB and 8GB
- SD card can choose 32GB and 64GB
ED-HMI2002-070C provides HDMI, USB 2.0, USB 3.0 and Ethernet interfaces, supporting access to the network through Wi-Fi and Ethernet.
ED-HMI2002-070C integrates 7-inch LCD touch screen and is mainly used in industrial control and IOT.
1.2 Rarangi Tarapi
· 1x ED-HMI2002-070C Waehe
1.3 Te ahua
Te whakauru i nga mahi me nga whakamaramatanga o nga atanga ki ia panui.
1.3.1 Paewhiri Mua
Ko tenei waahanga e whakaatu ana i nga mahi me nga whakamaramatanga o te papa o mua.
1.3.2 Paewhiri Whakamuri
Ko tenei waahanga e whakaatu ana i nga atanga me nga whakamaramatanga o te panui o muri.
1.3.3 Paewhiri Taha
Ko tenei waahanga e whakaatu ana i nga atanga me nga whakamaramatanga o te paewhiri taha.
1.4 Tohu
Ko tenei waahanga e whakaatu ana i nga ahuatanga me nga tikanga o nga tohu kei roto i te EDHMI2002-070C.
1.5 Atanga
Te whakauru i te whakamaramatanga me te mahi o ia atanga i roto i te hua.
1.5.1 Tuku Hiko
Kei roto i te ED-HMI2002-070C tetahi whakauru hiko, a ko te mata hiraka ko "PWR IN". Ko te hononga he USB Momo-C, e tautoko ana i te whakauru hiko 5V 3A.
TIP
Kia pai ake ai te mahi a Raspberry Pi 4, ka tūtohuhia kia whakamahia he taputapu hiko 5V 3A.
1.5.2 1000M Itarangi
1.5.3 Ororongo
The ED-HMI2002-101C device contains 1 audio interface, 3.5mm four-section headphone terminal, and the silkscreen is “
“. It supports OMTP specification stereo headphone output and single channel microphone recording.
1.5.4 HDMI
Kei roto i te ED-HMI2002-070C nga tauranga HDMI 2, a ko te mata hiraka ko "HDMI". Ko te hono he microHDMI, ka taea te hono ki nga whakaaturanga HDMI me te tautoko ki te 4Kp60.
1.5.5 USB2.0
ED-HMI2002-070C includes 2 USB 2.0 ports, and the silkscreen is “
“. The connector is USB Type-A, which can connect to standard USB 2.0 peripherals and supports up to 480Mbps.
1.5.6 USB3.0
ED-HMI2002-070C includes 2 USB 3.0 ports, and the silkscreen is “
“. The connector is USB Type-A, which can connect to standard USB 3.0 peripherals and supports up to 5Gbps.
2 Tāuta Pūrere
Ko tenei upoko e whakaatu ana i nga mahi motuhake mo te whakauru i te taputapu.
2.1 Tāuta Rahipere Pi 4 (kōwhiringa)
If the product model purchased by the customer does not include Raspberry Pi 4, Raspberry Pi 4 needs to be installed first.
Whakaritenga
- ED-HMI2002-070C and SD card have been obtained from the packaging box.
- Raspberry Pi 4 is ready.
- Kua whakaritea he huriwiri ripeka.
Nga hikoinga
- Insert the SD card into SD card slot of Raspberry Pi 4.
- Use a screwdriver to loosen 4 M3 screws on ED-HMI2002-070C case counterclockwise, and remove the case.
- Use a screwdriver to loosen 3 M2.5 screws on ED-Pi4PCOOLER counterclockwise, and remove the cooler.
TIP
– ED-Pi4PCOOLER is an optional cooling accessory.
– If there is a film of thermal conductive silicone, please remove it . - Place the Raspberry Pi 4 on the back of the LCD screen so that the installation holes of the Raspberry Pi 4 can align with the four stud holes on the back of the LCD screen.
- Pass the FPC cable through the reserved hole on the ED-Pi4PCOOLER.
- Plug the FPC cable into the CAMERA and DISPLAY ports of the Raspberry Pi 4 respectively.
- Make 3 mounting holes of ED-Pi4PCOOLER aligning with the mounting holes of Raspberry Pi 4.
- Insert 3 M2.5*12 screws and 1 M2.5*5 screw, then tighten them clockwise to secure the Raspberry Pi 4 and ED-Pi4PCOOLER to the back side of the LCD screen.
- Plug the power cord into the corresponding 40-Pin on the Raspberry Pi 4.
- Cover the case, insert 4 M3 screws, and tighten clockwise to fix the case to the back of the LCD screen.
2.2 Tāuta Tāmau
Ka tautokohia e te taputapu ED-HMI2002-070C te whakaurunga o mua. Ko te Paerewa Paerewa kaore i te whakauru i nga taputapu whakakao, tena koa hoko mai i te ED-ACCHMI-Mua mai i a maatau kaihoko.
Whakaritenga
- ED-ACCHMI-Front accessory kit has been obtained (contains 4xbuckles, 4xM4*10 screws and 4xM4*16 screws).
- Kua whakaritea he huriwiri ripeka.
Nga hikoinga
1. ensure the opening size of the cabinet according to the size of ED-HMI2002-070C, as shown in the figure below.
2. Toia he kohao ki runga i te rūnanga kia rite ki te rahi o te kohao o te taahiraa1.
3. Embed the ED-HMI2002-070C into the cabinet from the outside.
4. Tiarohia te kohao tīwiri (poka kore mirohia) o te maara ki te kohao whakauru i runga i te taputapu.
5. Whakamahia kia 4 M4*10 tīwiri ki te haere i roto i te peera me te whakakikī i te reira karaka ki te whakatika i te mapere ki te taputapu; ka whakamahi 4 M4*16 tīwiri ki te haere i roto i te kohao tīwiri (poka miro) o te peera, me te titi karaka ki te pito i roto i nga peera.
3 Whakarewa i te Pūrere
Ko tenei upoko e whakaatu ana me pehea te hono i nga taura me te whakaara i te taputapu.
3.1 Hononga taura
Ko tenei waahanga e whakaatu ana me pehea te hono i nga taura.
Whakaritenga
- Ko nga taputapu penei i te whakaatu, te kiore, te papapātuhi me te urutau hiko ka taea te whakamahi i te tikanga kua rite.
- He whatunga ka taea te whakamahi noa.
- Tikina te taura HDMI me te taura whatunga ka taea te whakamahi noa.
Hoahoa hoahoa o nga taura hono:
Tena tirohia te 1.5 Atanga mo te whakamaramatanga titi o ia atanga me te tikanga motuhake mo te waea.
3.2 Whakaara Te Pūnaha Mo te Wa Tuatahi
ED-HMI2002-070C karekau he pana hiko. I muri i te hono o te hiko, ka timata te punaha.
Ka whakauruhia te hua ki te punaha putanga Papamahi ina wehe atu i te wheketere. I muri i te tiimata o te taputapu, ka uru tika ki te papamahi.
TIP
Ko te ingoa kaiwhakamahi taunoa he pi, ko te kupuhipa taunoa ko te rōpere.
or more information about Raspberry Pi 4 configuration operations, please refer to the documentation on the Raspberry Pi official website. The documentation path is: Raspberry Pi (https://www.raspberrypi.com/).
4 Takiuru Mamao
Ko tenei upoko e whakaatu ana me pehea te takiuru mamao i te taputapu.
4.1 Rapu IP Pūrere
te kimi IP taputapu
4.2 Hononga Ki te Papamahi Pūrere Na roto i te VNC
After the device starts normally, you can choose to remotely connect to the device through VNC to configure or debug it.
Whakaritenga:
- Ko te RealVNC Viewer tool has been installed on PC.
- Kua honoa a ED-HMI2002-070C ki te whatunga ma te pouara.
- IP address of ED-HMI2002-070C has been get.
- The VNC function in the ED-HMI2002-070C system has been turned on, as shown in the following figure.
Hipanga:
1. Whakatuwheratia te RealVNC Viewer ka kowhiri "Hononga hou ..." i roto i te File i roto i te pae tahua hei whakatuwhera i te matapihi mo te hanga hononga, penei i te ahua e whai ake nei.
2. I muri i te whakauru i te IP IP o ED-HMI2002-070C, pawhiria te "OK".
3. E tomo te ingoa kaiwhakamahi me te kupuhipa i roto i te Motuhēhēnga pouaka wawe e pops ake.
TIP
Ko te ingoa kaiwhakamahi taunoa he pi, ko te kupuhipa taunoa ko te rōpere.
4. Tīpakohia "OK" ki te takiuru me te hono ki te papamahi mamao.
5 Tāuta OS (kōwhiringa)
- If you are purchasing a device without Raspberry Pi 4 and SD card, the device does not come with an operating system by default. Raspberry Pi 4 needs to be installed first, then you need to install os. Our company supports to install the OS by installing the standard Raspberry Pi OS first, and then install the Firmware package.
- If you are purchasing a device with Raspberry Pi 4 and SD card, the device is shipped with an operating system by default. If the OS is corrupted during use or the user needs to replace the OS, it is necessary to re-download the appropriate system image and install it. Our company supports to install the OS by installing the standard Raspberry Pi OS first, and then install the Firmware package.
Ko te waahanga e whai ake nei e whakaatu ana i nga mahi motuhake o te tango whakaahua, te kaari SD me te whakaurunga o nga kohinga Firmware.
TIP
Tena koa kia whakaurua e koe to maatau kete Firmware i muri i to whakaurunga Paerewa Raspberry Pi OS, mena ka kore te whakaaturanga me te pa e mahi.
5.1 Tikiake OS File
Ka taea e koe te tango i te Raspberry Pi OS whai mana file kia rite ki o hiahia ake, kua whakarārangihia te ara tango i raro nei:
5.2 Tiro ana ki te Kaari SD
E taunaki ana kia whakamahia nga taputapu mana o Raspberry Pi. Ko nga huarahi tango e whai ake nei:
- Rahipere Pi Atahanga : https://downloads.raspberrypi.org/imager/imager_latest.exe (https://downloads.raspberrypi.org/imager/imager_latest.exe)
- Kaiwhakahōputu Kāri SD : https://www.sdcardformatter.com/download/ (https://www.sdcardformatter.com/download/)
Whakaritenga:
- Kua oti te tango me te whakaurunga o nga taputapu mana ki te rorohiko.
- An SD card reader has been prepared.
- Ko te OS file kua whiwhi.
Hipanga:
Ko nga taahiraa e whakaahuahia ana ma te whakamahi i te punaha Windows hei tauiraample.
1. Open the device case, then pull out SD card.
a. Remove the metal case of the ED-HMI2002-070C by unscrewing the 4 M3 screws on the metal case counterclockwise with a screwdriver.
b. Remove the Raspberry Pi 4 by unscrewing the four screws that mount the Raspberry Pi 4 counterclockwise with a screwdriver.
c. Pull out SD card from SD card slot of Raspberry Pi 4.
2. Kōkuhu te kāri SD ki te kaipānui kāri, a ka kōkuhu i te kaipānui kāri ki te tauranga USB o tō rorohiko.
3. Open SD Card Formatter, tīpako i te reta puku whakahōputu, ka pāwhiri "Hōputu" i te raro matau ki te whakahōputu.
4. I roto i te pouaka akiaki pakū-ake, tīpako "Ae".
5. Ina oti te whakahōputu, pawhiria te "OK" i te pouaka akiaki.
6. Katia te Whakahōputu Kāri SD.
7. Whakatuwherahia te Raspberry Pi Imager, tohua te "KOKOHI OS" ka kowhiri i te "Whakamahia Ritenga" i roto i te pihanga pakū-ake.
8. E ai ki te akiaki, tohua te OS file i raro i te ara kua tautuhia e te kaiwhakamahi ka hoki ki te wharangi matua.
9. Patohia te "KOKOWHIRINGA KAUPAPA", tohua te taputapu taunoa i roto i te atanga "Storage", ka hoki ki te wharangi matua.
10. Pāwhiritia "NEXT", tīpako "NO" i roto i te pakū-ake "Whakamahia OS whakaritenga?" pihanga.
11. Tīpakohia "ĀE" i roto i te pahū-ake "Whakatupato" pihanga ki te tīmata te tuhi i te whakapakoko.
12. Ka oti te tuhi OS, te file ka whakamanahia.
13. I muri i te whakaotinga o te manatoko, pawhiria te "TONO" i roto i te pouaka pahū-ake "Tuhia Angitu".
14. Close the Raspberry Pi Imager, remove the SD card. 15. Insert the SD card into the SD card slot of the Raspberry Pi 4 and close the device case.
a. Whakauruhia te kaari SD ki te mokamoka kaari SD o te Raspberry Pi 4.
b. Whakaorangia te Raspberry Pi 4 ma te whakamau i nga taarua e 4 mo te whakairi i te Raspberry Pi 4 ki te taha karaka me te huriwiri.
c. Whakapaia nga karaka 4 M3 i runga i te pouaka whakarewa o te ED-HMI2002-070C ki te karaka ki te huriwiri ka kati te pouaka taputapu.
5.3 Tāuta Mōkī Firmware
I muri i te whakauru i te OS Raspberry Pi paerewa i runga i te ED-HMI2002-070C.Me whirihora e koe te punaha ma te taapiri i te puna edatec apt me te whakauru i te kete firmware kia pai ai te mahi o te punaha. E whai ake nei he exampLe o Debian 12 (pukapuka) putanga papamahi.
Whakaritenga:
- The flashing to SD card of the Raspberry Pi standard OS (bookworm) has been completed.
- Kua rewa te taputapu me te whirihoranga whawhai e tika ana kua oti.
Īmēra: sales@edatec.cn / support@edatec.cn
Web: www.edatec.cn
Waea: +86-15921483028(Haina) | +86-18217351262(Tawahi)
Tuhinga / Rauemi
 |
Hangarau EDA ED-HMI2002-070C Ahumahi Aunoa me te Whakahaere [pdf] Pukapuka Kaiwhakamahi ED-HMI2002-070C, ED-HMI2002-070C Ahumahi Aunoa me te Whakahaere, ED-HMI2002-070C, Ahumahi Ahumahi me te Whakahaere, Te Aunoa me te Whakahaere, Te Mana |