EVENT LIGHTING APRO4-IP DMX Controller

Mo to haumaru, panuihia tenei pukapuka kaiwhakamahi i mua i te whakamahi.
Ko te Maama Takahanga te mana ki te whakahou i te pukapuka i nga wa katoa. Ko nga korero me nga korero i roto i tenei pukapuka ka taea te whakarereke me te kore panui. Karekau he kawenga, he kawenga ranei mo nga hapa me nga hapa o te Maama Takahanga. Tena koa korero mo te Maama Takahanga mo nga whakamarama me nga korero mo tenei mea.

NGA WHAKAMAHI

• DMX 512, RDM, Artnet and sACN support
• whirihoranga mamao ma roto webwharangi
• Update firmware on Webwharangi
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• Whakaaturanga LCD
• Gigabit network, 100/1000mbps port speed
• Whakatauranga IP65

PANELA NUIVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Puka pupuri
7. LCD Display protection cover

MENU
Below is controller Menus map

MatuaTahua	Tahua Raro 1	Tahua Raro 2	Uara/Kōwhiringa	Taunoa
Whatunga	Aratau IP		DHCP	Pahekeheke
			Pahekeheke
	Wāhitau IP		2.xx.xx.xx	2.xx.xx.xx
	Kopare Subnet		255.0.0.0	255.0.0.0
Tauranga DMX	Kawa	Artnet		Artnet
		SACN
	Start Net		000–127	000
	Tīmata Universe		000–255	000
	Tauranga 1	Aratau	Wehe	On
			On
		NET	000–127	000
		Te Ao	000–255	000
	Tauranga 2	Aratau	Wehe	On
			On
		NET	000–127	000
		Te Ao	000–255	001
	Tauranga 3	Aratau	Wehe	On
			On
		NET	000–127	000
		Te Ao	000–255	002
	Tauranga 4	Aratau	Wehe	On
			On
		NET	000–128	000
		Te Ao	000–255	003
			Monokia
Tautuhinga	Reiti DMX		20Hz	30Hz
			25Hz
			30Hz
			35Hz
			40Hz
	RDM	Monokia		Monokia
		Whakahohe
	Whakaatu Ana	I nga wa katoa		1Min
		30Mana
		1Min
		5Min
	Ngaronga Tohu	Kia mau te DMX		Kia mau te DMX
		Stop Output
	Aratau Hanumi	HTP		HTP
		LTP
	wheketere Tautuhi	Kao		Kao
		Ae

WEB whirihoranga

NET device network IP mode can set to DHCP mode or Static mode.

Aratau DHCP

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Enter IP address in your web browser, then you can login webpage to configure the parameter of controller.

Whakauruhia te kupuhipa: admin

Aratau pateko

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Then set the IP address of computer is in the same IP range manually. For example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Whakauruhia te kupuhipa: admin

• When log on NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• For DMX Port page , it is used for DMX Port setting. You can select Protocol to be Artnet or sACN, and set each port as input or output.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Ngaronga Tohu: Can set as Hold DMX or Stop Output.
• You can return to factory setting by click Factory Reset button.
• On Update page, you can update software of fixture by selecting the update software file of APRO4‐IP.
• On the last page, you can reset password.

WHAKAMAHI

• Mana i roto i: AC 100‐240V,50/60Hz
• Kohi hiko: AC240V 50HZ 0.05A
• Rahi: 215.3×150.5x42mm 4.2W
• Taumaha: 1.43Kg
• POE 802.3af
• IP65

NGA AHU

Pūtāhui

Tena koa tirohia to kaihoko o to rohe, waea atu ranei ki te Maama Takahanga. www.event‐lighting.com.au

Pātai Auau

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Tuhinga / Rauemi

EVENT LIGHTING APRO4-IP DMX Controller [pdf] Pukapuka Kaiwhakamahi APRO4-IP, APRO4-IP DMX Controller, DMX Controller, Controller

Tohutoro

• Pukapuka Kaiwhakamahi