IDEC HG1J PCAP Touchscreen Operator Interface

Whakatakotoranga Hua

Whakatakotoranga Whānui

Here’s the data from the image properly formatted in table form:

Tūemi	Whakatakotoranga
Kua whakatauhia te mana voltage	12/24V DC
Mana voltage awhe	10.2 ki te 28.8V DC
Kohi hiko	4W maximum when not using USB1 or USB2 3W maximum when Backlight OFF 12W mōrahi
Allowable momentary power interruption	10ms max. (power supply voltage 20.4V DC) 1ms max. (power supply voltage 10.2V DC)
Ko te urunga o naianei	40A mōrahi
Te kaha dielectric	500V AC, 5mA, 1 minute between power and FG terminals
Te pāmahana whakahaere	-20 to +55°C (no freezing) (*1)
Te haumākū whakahaere	10 to 95%RH (no condensation) (*2)
Te pāmahana rokiroki	-20 to +70°C (no freezing) (*1)
Te haumākū rokiroki	10 to 95%RH (no condensation) (*2)
Te tohu parahanga	2
Te ātete wiri	5 to 8.4Hz single amprama 3.5mm, 8.4 to 150Hz acceleration, 9.8M/s² on each of 3 mutually perpendicular axes (IEC 61131-2)
Te parenga ohorere	147m/s², 11ms, 3 shocks on each of 6 directions in X, Y, and Z 3 axes (IEC 61131-2)
Ngangau immunity	Fast transient/burst test Power terminals: 2kV Communication line: 1kV (IEC/EN 61131-2)
Te tukunga hiko	Contact: 6kV Air: 8kV (IEC/EN 61131-2)
Corrosion immunity	Karekau mai i nga hau haupapa
Whakaeke	Panel mount (panel thickness: 1.0 to 5.0mm)
Te tohu tiaki	IP65F (IEC 60529) When panel thickness is between 1.6 to 5mm: IP66F, IP67F (IEC 60529) TYPE 4X, TYPE 13
Ahu	123.8 (W) × 86.5 (H) × 41.3 (D) mm
Taumaha (approx.)	260g

1. Avoid prolonged use of the product in direct sunlight, as this can increase the surface temperature of the display above the ambient temperature, causing touch panel malfunctions.
2. Avoid using the product in areas exposed to excessive hot water, as sudden temperature changes can cause condensation inside the product, leading to malfunctions.

• Screen types Base screen, popup screen, system screen
• No. of screens Base screen: 3000 max.
  • Popup screen: 3015 max.
• User memory Approx. 24MB
• Nga waahanga
• Bit Button, Word Button, Goto Screen, Print Button, Key Button, Multi Button, Keypad, Numerical Input, Character Input, Pilot Lamp, Multi-State Lamp, Picture Display, Message Display, Message Switching Display, Alarm List Display, Alarm Log Display, Data Log Display, Numerical Display, Bar Graph, Trend Chart, Pie Chart, Meter, Calendar, Bit Write Command, Word Write Command, Goto Screen Command, Print Command, Timer, Screen Script Command, Multi Command
• Maramataka
  • Year, Month, Day, Hour, Min., Sec., Day of Week±60 sec per month (at 25°C)
• Power failure backup data Calendar, log data, keep relay, internal register
• Backup time 20 days (Typ.) (*3)
  • If the power is cut off for more than 20 days, the error message “Backup data lost” will be displayed at the next start-up and the clock data will be initialized to “00:00:00 January 1, 2000”. Log data, keep relay, and internal register.

Whakatakotoranga Atanga

Atanga	Kaihono	Nga ahuatanga hiko	Te tere tuku	Tukutahi	Tikanga korero	Pūnaha whakahaere
Serial interface (COM)
RS232C	Detachable 10-pin terminal block	EIA RS232C compliant	1200 / 2400 / 4800 / 9600 / 19,200 / 38,400 / 57,600 bps	Tukutahi	Half or full duplex	Hardware control or none
RS422/485	Detachable 10-pin terminal block	EIA RS422/485 compliant	1200 / 2400 / 4800 / 9600 / 19,200 / 38,400 / 57,600 / 115,200 / 187,500 bps	Tukutahi	Half or full duplex	Karekau
Atanga Itarangi (LAN)	Modular connector (RJ-45)	IEEE802.3u (10BASE-T / 100BASE-TX) compliant	—	—	—	—
USB interface (USB1) (*6)	Tuhono USB Momo A	USB 2.0 High speed (480 Mbps)	—	—	—	—
USB interface (USB2) (*6)	Tuhono USB Momo A	USB 2.0 High speed (480 Mbps)	—	—	—	—

• RS232C and RS422/485 can be used simultaneously.
• 187,500 bps is available only with , SIEMENS SIMATIC S7-300/400 series (MPI port direct connection).
• USB output current varies depending on the mounting direction and operating temperature.

Serial Interface Connector Terminal Arrangement

Nga Tohutohu Whakamahi Hua

Mahi Mata Paa:
The PCAP touchscreen is designed for easy operation with multi-touch functionality. Ensure to use the touchscreen with clean hands or stylus for optimal performance.

Te horoi me te tiaki:
Use wipes soaked in alcohol or disinfectant to clean the tempered glass surface. Avoid using abrasive cleaners that may scratch the glass.

Te Pumautanga o te Taiao:
With exceptional environmental durability, the product can withstand a wide range of temperatures and high water resistance. Ensure to apply a UV protective film if exposed to direct sunlight for extended periods.

Sleek, functional, and durable glass-top design with integrated IoT networking capabilities

The touch panel surface is made of tempered glass, providing clear visibility and high transparency for easy readability even in bright working environments.

Tempered glass remains clear over time and is resistant to clouding from age or UV exposure.

Awhe pāmahana whanui

Excellent waterproof performance, can be used in wet environments.

MQTT compliant, can connect to cloud platforms.

EtherNet/IP™ compatible, enabling seamless connection to PLCs from various manufacturers.

Slimline bezel design maximizes the display area
The slim bezel on the HT1J and HT2J maximizes screen space, offering a more expansive display.

Multi-touch touchscreen designed to resist mechanical deterioration

• Conventional analog resistive touchscreens are not so well protected against mechanical deterioration. This is because the transparent conductive electrodes and film move with each press of the panel. The PCAP touchscreen uses a sensor board to detect changes in electrical charge to identify where the touchscreen was pressed. As the surface is made of tempered glass, there are no moving parts, allowing for lighter and more agile operations without deterioration.
• The PCAP touchscreen also prevents unintended activation by water droplets, and can be used while wearing rubber gloves or gloves less than 1.5mm thick1.
• 1 The touchscreen may not work with gloves thicker than 1.5mm, depending on the material of

Glass-top structure offers excellent hygienic characteristics

• The glass surface resists scratches and is sealed against water, oil, and the ingress of dirt. The glass can be cleaned with wipes soaked in alcohol or disinfectant.
• Tuhipoka: Tirohia website for details on disinfection methods and the effect that they will have on the product.

Karaihe whakamarumaru 

• Stronger than regular glass, the tempered glass passed a drop test with a 1kg steel ball (dropped onto the center of the glass from a height of 60cm).
• Tuhipoka: Results are from in-house testing and do not guarantee the performance of the product.
• An optional protective film is available to prevent the glass from scattering when broken by impact.

Exceptional environmental durability for diverse applications

Wide range of operating temperatures

• Suitable for use in hot and cold environments ranging from -20 to +60°C1.
• 1. No freezing.
  • The upper limit of HG1J is 55°C.

High water resistance

• IP66F / IP67F protection. Resistant to direct water jets.

Retains its clarity for years

• Conventional products with a plastic film on the surface will cloud over time, reducing visibility due to prolonged UV light exposure. In contrast, the HG1J and HG2J has a glass top that maintains high visibility and prevents deterioration and clouding from exposure to UV rays over a long period of time2.
• 2. If the product is used in a location where it may be exposed to UV rays for a long period of time (e.g., near a window), apply a UV protective film to prevent degradation of non-glass parts.

Advanced connectability

Extensive external interfaces

Easily connect to RS232C, RS422/485, Ethernet and USB-A ports, PLCs, barcode readers and other external devices and interfaces. The power supply and serial interface are push-in type terminals enabling safety and maintainability. Wiring is reduced to one quick and simple step.

Easily connected to versatile USB devices 3

• Plug a USB speaker into the USB-A port for audio output.
• Plug a Wi-Fi dongle into the USB-A port to wirelessly connect to a PC or tablet.

Tono example

• The operational status of machines equipped with the touch panel can be communicated to nearby workers with sound. The workers do not need to look at the machines to confirm their status. This system can improve efficiency and prevent distractions/incidents caused by having to look away from other tasks.

IoT-compatible

Various IoT functions 
A wide range of IoT-related functions ensure that the HG1J and HG2J can be seamlessly integrated with various other compatible devices.

• Subject to change depending on specifications and service updates.

Web server function enables remote operation and maintenance from tablets

• The operator interface can be checked and operated from standard web browsers on a tablet, PC, or smartphone. No special software or additional licenses required. Furthermore, the custom web page function allows the browser to display a screen that differs from the one displayed on the operator interface.

Nga tono examples

• In logistics warehouses and other large facilities, equipment is spread out across a wide area. It can take time to visit each machine, check the current status and run processes. Using the web server function, you can check and operate all equipment from a tablet – no matter where in the facility you are at the time.

Supports various communication functions

Gateway between manufacturing sites and the cloud 
Open protocols including EtherNet/IP and Modbus TCP are supported – as are communication protocols with PLCs from various manufacturers. Your HG1J or HG2J device acts as a gateway between your manufacturing site and the cloud. Reading data from various devices, such as PLCs, and forwarding it to cloud storage with MQTT communication is simple.

MQTT

• Supports MQTT communication, ideal for IoT applications.
• Direct connection to the server without a gateway.
• Supports authentication by certificate in addition to ID and password.

EtherNet/IP™

• Supports EtherNet/IP without the need for additional devices.
• Connects to both scanner and adapter devices.

Social media and email function
The device status can be sent by email and to multiple X (Formerly Twitter) accounts.

Tono example

• Checking a nationwide system of connected devices (e.g., payment machines at car and bicycle parking lots) is not an easy task. Such a wide network requires a central, unique web pūnaha.
• When using the HG1J and HG2J, multiple devices can share their current status on social media – all immediately visible in your news feed.

No battery replacement required

Battery-free design eliminates the need for battery replacement

• General data is stored in Non-volatile memory, and clock data uses a hyper capacitor, that does not require batteries. No batteries also means no need to fill out extra paperwork to ship controllers internationally.

Pūmanawa ngawari ki te whakamahi

• Available with Automation Organizer.

HG1J Operator Interface

• Compact yet powerful displays designed for maximum efficiency.

HG1J

Ahu

• Dimensions in blue show the mounting dimensions of the cable.
• USB and LAN interfaces are as shown in the dimensional drawings above.
• When installing, take into consideration the space required for your USB device or LAN cable.
• Install the operator interface into a panel cut-out by tightening the two mounting clips (supplied) to a torque of 0.3 to 0.4 N·m.
• Do not tighten with excessive force, otherwise the main unit may become distorted and waterproof characteristics may be lost.

Mounting hole layout

• Panel thickness: 1.0 to 5.0mm

HG2J Operator Interface

Simplify operations with intuitive HMI and versatile functionality.

HG2J

Whakaatu mata	Kāhua mahi	Atanga whakawhitiwhiti	Tae Bezel	Whakaaetanga	Wahi No.
7-inch wide TFT color LCD 65,536 colors	PCAP touchscreen (Projected capacitive)	COM LAN USB1 USB2	Pango	UL 61010-1 UL 61010-2-201 UL 121201 CSA C22.2 No.61010-1-12 CSA C22.2 No.61010-2-201 CSA C22.2 No.213	HG2J-7UT22TF-B

Ahu

• Dimensions in blue show the mounting dimensions of the cable.
• USB and LAN interfaces are as shown in the dimensional drawings above.
• When installing, take into consideration the space required for your USB device or LAN cable.
• Install the operator interface into a panel cut-out by tightening the four mounting clips (supplied) to a torque of 0.5 to 0.6 N·m.
• Do not tighten with excessive force, otherwise the main unit may become distorted and waterproof characteristics may be lost.

Mounting hole layout

• Panel Thickness: 1.0 to 5.0mm

Whakatakotoranga Whānui

• Kua whakatauhia te mana voltage 12/24V DC
• Mana voltage awhe 10.2 ki 28.8V DC
• Kohi hiko
  • 5W maximum when not using USB1 or USB2
  • 3W maximum when Backlight OFF
  • 13W mōrahi
• Allowable momentary power interruption
  • 10ms max. (power supply voltage 20.4 to 28.8V DC)
  • 1ms max. (power supply voltage 10.2 to 20.4V DC)
• Inrush current 40A maximum
• Dielectric strength 500V AC, 10mA, 1 minute between power and FG terminals
• Operating temperature -20 to +60°C (no freezing) (*1)
• Operating humidity 10 to 90%RH (no condensation) (*2)
• Storage temperature -20 to +70°C (no freezing) (*1)
• Storage humidity 10 to 90%RH (no condensation) (*2)
• Tohu parahanga 2
• Te ātete wiri
  • 5 to 8.4Hz single amplitude 3.5 mm, 8.4 to 150Hz acceleration, 9.8M/s2 on each of 3 mutually perpendicular axes (IEC 61131-2)
• Te parenga ohorere
  • 147m/s2, 11ms, 3 shocks on each of 6 directions in X, Y, and Z 3 axes (IEC 61131-2)
• Ngangau immunity
  • Fast transient/burst test
  • Power terminals: 2kV
  • Communication line: 1kV (IEC/EN 61131-2)
• Electrostatic discharge Contact: 6kV
• Air: 8kV (IEC/EN 61131-2)
• Corrosion immunity Free from corrosive gases
• Mounting Panel mount (panel thickness: 1.0 to 5.0mm)
• Te tohu tiaki
  • When panel thickness is between 1 to 5mm: IP65F (IEC 60529)
  • When panel thickness is between 1.6 to 5mm:IP66F, IP67F (IEC 60529) TYPE 4X, TYPE 13
• Ahu 186 (W) x 128 (H) x 30.4 (D) mm
• Weight (approx.) 500g
• 1) Avoid prolonged use of the product in direct sunlight, as this can increase the surface temperature of the display above the ambient temperature, causing touch panel malfunctions.
• 2) Avoid using the product in areas exposed to excessive hot water, as sudden temperature changes can cause condensation inside the product, leading to malfunctions.

Whakaaturanga Whakaaturanga

Whakaritenga Mahi

• Switching element PCAP (Projected capacitance) method
• Multiple operations Up to 2 points
• Acknowledgment sound Electronic buzzer or audio output

Whakatakotoranga Taumahi

If the power is cut off for more than 20 days, the error message “Backup data lost” will be displayed at the next start-up and the clock data will be initialized to “00:00:00 January 1, 2000”. Log data, keep relay, and internal register.

Whakatakotoranga Atanga

Here’s your provided data clearly formatted in a professional table form:

• 4) RS232C and RS422/485 can be used simultaneously.
• 5) 187,500 bps is available only with , SIEMENS SIMATIC S7-300/400 series (MPI port direct connection).
• 6) USB output current varies depending on the mounting direction and operating temperature.

Serial Interface Connector Terminal Arrangement

Ingoa	Te aronga	Mahi	Whakawhitiwhiti
SD	KI WAHO	Tukuna raraunga	RS232C
RD	IN	Whiwhi raraunga	RS232C
RS	KI WAHO	Tono ki te tuku	RS232C
CS	IN	Maama ki te tuku	RS232C
SG	KI WAHO	Whenua tohu	RS232C, RS422/485
SDA	KI WAHO	Send data “+”	RS422/485
wharepaku	KI WAHO	Send data “–”	RS422/485
RDA	IN	Receive data “+”	RS422/485
RDB	IN	Receive data “–”	RS422/485

Nga taputapu

Here’s your provided data clearly formatted in a comprehensive and organized table form:

Tūemi	Ingoa / Hanga	Wahi No.	Te nui	Tauira e tika ana	Whakatakotoranga
System integration software	—	SW1A-W1C	1 (Includes WindO/I-NV4)	—	Automation Organizer software package
Protective film (Black bezel)		HG9Z-2D7	5	For HG2J / FT2J	Protective film to cover the panel surface. Rahi: 182.4 × 124.4 mm Matotoru: 0.153 mm
Protective film (Metallic bezel)	—	HG9Z-1E4	5	For HG1J / FT1J	Protective film to cover the panel surface. Rahi: 120.8 × 83.5 mm Matotoru: 0.135 mm
UV protective film (Black bezel)	—	FT9Z-2D7	5	For HG2J / FT2J	Protective film to cover UV over panel surface. Spray with water to attach. Rahi: 181.4 × 123.4 mm Matotoru: 0.135 mm
UV protective film (Metallic bezel)	—	FT9Z-1E4	5	For HG1J / FT1J	Protective film to cover UV over panel surface. Spray with water to attach. Rahi: 119.8 × 82.5 mm Matotoru: 0.135 mm
USB relay port (Black bezel)	CWIX-USB20-1M	—	1	For HG2J / FT2J	Install on control panels to connect the USB connector. Te roa o te taura: 1 m USB 2.0 Momo A.
USB relay port (Metallic bezel)	CW4X-USB20-1M	—	1	For HG1J / FT1J	Install on control panels to connect the USB connector. Te roa o te taura: 1 m USB 2.0 Momo A.
RJ45 relay port (Black bezel)	CWIX-RJ45	—	1	For HG2J / FT2J	Install on control panels to connect the LAN cable of the RJ45 connector. Te hononga atanga Itarangi
RJ45 relay port (Metallic bezel)	CW4X-RJ45	—	1	For HG1J / FT1J	Install on control panels to connect the LAN cable of the RJ45 connector. Te hononga atanga Itarangi
Potae rapa	CW9Z-D1X1	—	1	—	Protective rubber caps for USB relay port and RJ45 relay port. Rauemi: TPE Tae: Pango Protection: IP65/67
Uwhi kirihou	CW9Z-D1X2	—	1	—	Plastic cover for protection of USB relay port and RJ45 relay port. Material: Lens – Polycarbonate resin; Body – Polyamide resin; Packing – NBR Color: Translucent Protection: IP65/67
Power supply terminal connector (for changing wiring direction)	FT9Z-IX03V		1	For HG1J	Removable 3-pin push-in terminal block (not included with main unit). Used for changing the wiring direction.

1. Exclusive for CW series relay ports (CW1X /CW4X) and cannot be used for other models.
2. Refer to the instruction manual from the QR code on the right for details on how to use the product.

Ingoa	Topenga Whakauru	Tūhono Atanga Rangatū	Power Supply Terminal Connector
Hanga	HG9Z-4K2	HG9Z-XT09P	FT9Z-1TIOP
Wahi No.	HG9Z-4K2	HG9Z-XT09P	FT9Z-1TIOP
Te nui	1	1	1
Whakaahuatanga	For HGI J/HG2J 2 pieces (HGI J) or 4 pieces (HG2J) are included in the main unit.	For HG2J/FT2J Removable terminal block 9-pin, push-in type One plug is supplied with the main unit.	For HGI J/FTIJ Removable terminal block 10-pin, push-in type One plug is supplied with the main unit.

Compatible PLCs

Kaihanga	Rangatū
IDEC	MICROSmart FC6A
	SmartAXIS FT1A Pro/Lite
	MICROSmart FC6A (Ethernet)
	SmartAXIS FT1A Pro/Lite (Ethernet)
Mitsubishi	MELSEC-A (link unit)
	MELSEC-QnA (link unit)
	MELSEC-Q (link unit)
	MELSEC-Q (Ethernet)
	MELSEC-FX
	MELSEC-FX (Ethernet)
OMRON	SYSMAC-C
	SYSMAC-CS
	SYSMAC-CJ1
	SYSMAC-CJ2
	SYSMAC-CP1
	SYSMAC (Ethernet)
Allen-Bradley	PLC-5 (Half Duplex)
	SLC-500 (Half Duplex)
	MicroLogix (Full Duplex)
	ControlLogix (Full Duplex)
	CompactLogix (Full Duplex)
	FlexLogix (Full Duplex)
	ControlLogix (Ethernet/IP, Ethernet/IP (Logix Native Tag))
	CompactLogix (Ethernet/IP, Ethernet/IP (Logix Native Tag))
	PLC-5 (Ethernet/IP)
	SLC 500 (Ethernet/IP)
	MicroLogix (Ethernet/IP)

Kaihanga	Rangatū
SIEMENS	S7-200
	S7-300 (connect to CPU unit)
	S7-300 (link unit)
	S7-400
	S7-1200 (Ethernet)
Keyence	KV-700 / 1000 / 3000 / 5000 / 7000
	KV Nano
	KZ
	KV-10 / 16 / 24 / 40
	KV (Ethernet)
Shibaura Machinery	TC200
	TCmini
Modicon	Modbus RTU Master (*1)
	Modbus RTU Slave (*2)
	Modbus ASCII Master (*1)
	Modbus TCP Client (*1)
	Modbus TCP Slave (*2)
Panasonic	FP Series (MEWNET)
Yaskawa Hiko	MP
	MP (Ethernet)
Fuji Hiko	MICREX-SX
	MICREX-SX (Ethernet)
FIG	Totalflow G4/G5 (RS232C / 485)
	Totalflow G4/G5 (Ethernet)

• The compatible PLC information is for reference only (except for IDEC PLCs), and IDEC does not guarantee the operation of any other manufacturers’ PLC. When using other manufacturers’ PLCs, read their specifications and instruction manual carefully.
• The PLC must be operated correctly under the user’s responsibility.
• The company names and product names are registered trademarks or brand names.
  • 1) HG1J/HG2J can be connected to a slave or server devices.
  • 2) Master or client device can be connected to the HG1J/HG2J.

HG1J/HG2J Operator Interface

Tohutohu
Kia mahara ki te panui i te pukapuka tohutohu i mua i te mahi whakaurunga, waea waea, mahi tiaki ranei.

• For details on mounting, wiring, and maintenance, see the instruction manual from the below URL. HG1J: https://product.idec.com/?product=HG1J
• HG2J: https://product.idec.com/?product=HG2J-7U

• This product has been manufactured under strict quality control. However, if you intend to use this product in applications where failure of this equipment may result in damage to property or injury, ensure that it is used in conjunction with appropriate fail-safe backup equipment.
• Turn off the power to the product before starting installation, removal, wiring, maintenance, and inspection of the products. Otherwise, there will be a risk of electric shock or fire as well as damage to the equipment.
• Emergency and interlocking circuits must be configured outside of the HG1J/HG2J.
• Do not use touch switches and the function keys for an emergency circuit or an interlocking circuit. If the HG1J/HG2J fails, external equipment connected to the HG series will no longer be protected, and serious injury to operators and equipment damage  may be caused.
• Use the product within the environmental limits given in the catalog and manual. Use of the product in high-temperature or high-humidity environments, or in locations where it is exposed to condensation, corrosive gas or large shock loads, can create the  risk of electrical shock or fire.
• The HG1J/HG2J is designed for use in pollution degree 2. Use the HG1J/HG2J in environments of pollution degree 2. (based on the IEC60664-1 rating)
• Install the HG series according to the instructions in the User’s Manual. Improper installation will result in falling, failure, electrical shock, fire hazard, or malfunction of the HG series.
• Use a power supply of the rated value. Using a incorrect power supply may cause fire.
• The HG1J/HG2J uses “PS2” as DC power supply.  (based on the IEC / EN61131 rating)
• Use an IEC 60127 approved fuse on the power line outside the HG1J/HG2J. (Applicable when the equipment with built-in operator interface is exported to Europe.)
• When exporting the HG1J/HG2J to Europe, use an EU-approved circuit protector. (Applicable when the equipment embedded with the operator interface is shipped to Europe.)
• The touch panel built-in the HG1J/HG2J is made of glass. The touch panel will break if exposed to excessive shock. Be careful when handling the HG1J/HG2J.
• The protective film affixed on the display of the HG1J/HG2J is used to protect the product from scratches during transportation. Remove the protective film before use. If the protective film is not removed, depending on the operating environment, the film may become cloudy and adhere to the display part, making it difficult to remove.
• Do not press or scratch the touch panel and protection sheet with a hard object such as a tool.
• Do not install the HG1J/HG2J in areas subject to strong ultraviolet rays, as ultraviolet rays may impair the quality of the LCD.
• Note that small black and bright dots may show up on LCD Screen. This is not a failure or malfunction.
• The backlight life is not guaranteed and refers to the time until the brightness reduces by half after use at 25°C from the initial value. The actual life depends on operating environments and conditions.
• Protection degree refers to the front of the surface after mounting. Although the protection structure satisfies various testing conditions, operation is not guaranteed under certain environments. IP66F/IP67F oil-proof structure satisfies oil-proof test conditions listed in the appendix of Japanese Industrial Standard JIS C 0920. Operation is not guaranteed when using oil for a long period of time or oil that does not satisfy standards. Please test/check before use.
• Do not attempt to disassemble, repair or modify the product. Otherwise, electric shock, fire, or malfunction may occur.

Te Ota Nga Ture me nga Tikanga

Mauruuru koe mo te whakamahi i nga Hua IDEC.
Ma te hokoasing products listed in our catalogs, datasheets, and the like (hereinafter referred to as “Catalogs”) you agree to be bound by these terms and conditions. Please read and agree to the terms and conditions before placing your order.

1. Nga korero mo nga ihirangi o Putumōhio
   1. Ko nga uara kua whakatauhia, nga uara mahi, me nga uara tohu o nga hua IDEC kua whakarārangihia i roto i tenei Putumōhio he uara kua riro mai i raro i ia tikanga i roto i nga whakamatautau motuhake, kaore hoki e kii i nga uara kua riro i roto i nga tikanga whakakotahi.
      Ano hoki, he rereke te roa i runga i te taiao whakamahi me nga tikanga whakamahi.
   2. Ko nga raraunga tohutoro me nga uara tohutoro kua whakarārangihia i roto i nga Putumōhio mo nga kaupapa tohutoro anake, kaore e kii ka mahi tika te hua ki tera awhe.
   3. Ko nga korero / ahua me nga taonga o nga hua IDEC kua whakarārangihia i roto i nga Putumōhio ka huri, ka mutu ranei nga hoko me te kore panui, mo te whakapai ake me etahi atu take.
   4. Ko te ihirangi o Putumōhio ka huri ki te kore panui.
      Tuhipoka mo nga tono
2. Mena ka whakamahi nga hua IDEC me etahi atu hua, whakaūhia nga ture / ture me nga paerewa e tika ana.
   Waihoki, whakaūhia he hototahi nga hua IDEC ki o punaha, miihini, taputapu, me nga mea pera ma te whakamahi i raro i nga tikanga tuturu. Karekau he kawenga a IDEC mo te hototahi ki nga hua IDEC.
3. Ko te whakamahinga examples me te tono exampKo nga mea kua whakarārangihia i roto i nga Putumōhio mo nga kaupapa tohutoro anake. Na reira, i te wa e whakauru ana i tetahi hua, whakaūhia te mahi me te haumaru o nga taputapu, taputapu, me era atu i mua i te whakamahi. I tua atu, mo enei exampNa, karekau a IDEC e tuku raihana ki te whakamahi i nga hua IDEC ki a koe, karekau hoki a IDEC e tuku whakamana mo te mana o nga mana taonga hinengaro me te kore takahi i nga mana taonga hinengaro o te hunga tuatoru.
4. A, no te whakamahi i nga hua IDEC, kia tupato ki te whakatinana i nga mea e whai ake nei.
   1. Te whakamahi i nga hua IDEC e tika ana mo te whakatauranga me te mahi
   2. Hoahoa haumaru, tae atu ki te hoahoa taapiri me te hoahoa aukati kino e aukati ana i etahi atu kino me te kino ahakoa ka taka te hua IDEC
   3. Ko te waea me te whakaurunga e whakarite ana ka taea e te hua IDEC e whakamahia ana i roto i to punaha, miihini, taputapu, aha atu ranei ka taea te mahi me te mahi i runga i ona whakaritenga.
5. Ko te whakamahi tonu i tetahi hua IDEC ahakoa kua paheke te mahi ka puta he wera kino, he paoa, he ahi, me era atu mea na te kino o te whakamaarama, he aha ranei. Mahia te tiaki i ia wa mo nga hua IDEC me nga punaha, miihini, taputapu, me nga mea e whakamahia ana.
6. IDEC products are developed and manufactured as general-purpose products for general industrial products. They are not intended for use in the following applications, and in the event that you use an IDEC product for these applications, unless otherwise agreed upon between you and IDEC, IDEC shall provide no guarantees whatsoever regarding IDEC products.
   1. Whakamahia i roto i nga tono e hiahia ana kia nui te haumaru, tae atu ki nga taputapu whakahaere mana karihi, nga taputapu kawe waka (tereina / waka rererangi / kaipuke / waka / taputapu waka, me etahi atu), taputapu mo te whakamahi i nga waahi o waho, nga taputapu teitei, nga taputapu hauora, nga taputapu haumaru. , etahi atu taputapu, taputapu, aha atu ranei ka raru te ora, te hauora tangata ranei
   2. Whakamahia i roto i nga tono e hiahia ana kia nui te pono, penei i nga punaha whakarato mo te hau / wai / hiko, aha atu, nga punaha e mahi tonu ana mo nga haora 24, me nga punaha whakataunga.
   3. Whakamahia i roto i nga tono ka taea te whakahaere, te whakamahi ranei i te hua ka rereke mai i nga tohu, i nga tikanga / taiao kua whakarārangihia i roto i nga Putumōhio, penei i nga taputapu e whakamahia ana i waho, i nga tono ranei i nga taiao e pa ana ki te parahanga matū, ki te pokanoa hiko ranei Ki te hiahia koe ki te whakamahi i nga hua IDEC i roto i te i runga ake i nga tono, kia mohio koe ki te korero ki tetahi kaihoko hoko IDEC.

Nga tirotirohanga
Ka tono matou kia mahia e koe nga tirotirohanga mo nga hua IDEC e hokona ana e koe me te kore e whakaroa, me te mahara tonu ki te whakahaeretanga / tiaki mo te whakahaere i te hua i mua me te wa o te tirotiro.

Pūtāhui

1. wā pūtāhui
   The warranty period for IDEC products shall be three (3) years after purchase or delivery to the specified location. However, this shall not apply in cases where there is a different specification in the Catalogs or there is another agreement in place between you and IDEC.
2. Te whānuitanga o te taurangi
   Mena ka puta he korenga i roto i tetahi hua IDEC i roto i te waa whakamana i runga ake nei mo nga take e pa ana ki te IDEC, katahi ka whakakapi, ka whakatika ranei a IDEC i taua hua, kaore he utu, i te waahi hoko / waahi tuku o te hua, he turanga ratonga IDEC ranei. Heoi, ko nga rahunga i puta mai i nga take e whai ake nei ka kiia i waho o te waahi o tenei whakamana.
   1. The product was handled or used deviating from the conditions / environment listed in the Catalogs
   2. Ko te rahunga i puta mai i nga take i tua atu i te hua IDEC
   3.  Ko te whakarereke, te whakatika ranei i mahia e tetahi roopu ke atu i te IDEC
   4. Ko te rahunga i takea mai i tetahi papatono rorohiko a tetahi atu i tua atu i te IDEC
   5. I whakamahia te hua ki waho o tana kaupapa taketake
   6. Ko te whakakapinga o nga waahanga tiaki, te whakaurunga o nga taputapu, nga mea pera ranei kaore i tika te mahi i runga i te pukapuka a te kaiwhakamahi me nga Putumōhio.
   7. Ko te kore i taea te matapae me nga paerewa pūtaiao me te hangarau i te wa i tukuna mai ai te hua mai i te IDEC
   8. Ko te korenga na etahi atu take ehara i te IDEC (tae atu ki nga keehi o te kaha majeure penei i nga aitua taiao me etahi atu aitua)

I tua atu, ko te raihana e whakaahuatia ana i konei e tohu ana ki te raihana mo te hua IDEC hei waeine, me nga pakaru i puta mai i te korenga o tetahi hua IDEC ka kapea mai i tenei raihana.

Te herenga o te taunahatanga
Ko te raihana kua whakarārangitia i roto i tenei Whakaaetanga ko te raihana katoa mo nga hua IDEC, a ka kore he taunahatanga a IDEC mo nga pakaru motuhake, nga pakaru autaki, nga pakaru ohorere, nga kino kino ranei i puta mai i tetahi hua IDEC.

Te whānuitanga o nga ratonga
Ko nga utu o nga hua IDEC kaore e uru ki nga utu o nga ratonga, penei i nga kaitoi tuku. Na reira, me utu motuhake i roto i nga keehi e whai ake nei.

1. Nga tohutohu mo te whakaurunga / whakatikatika me te haere tahi i nga mahi whakamatautau (tae atu ki te hanga rorohiko tono me te mahi whakamatautau, me etahi atu)
2. Nga tirotiro tiaki, whakatikatika, me te whakatikatika
3. Nga tohutohu hangarau me nga whakangungu hangarau
4. Nga whakamatautau hua, nga tirotirohanga ranei i tohua e koe

Ko nga korero o runga ake nei e mau ana i nga whakawhitinga me te whakamahi i roto i to rohe. Tena koa korero ki tetahi kaihoko hokohoko IDEC mo nga whakawhitinga me te whakamahi i waho o to rohe. Ano hoki, karekau he taurangi a IDEC mo nga hua IDEC e hokona ana i waho o to rohe.

HG1J/HG2J Operator Interface

Smart RFID Reader

IP65 and IP67F rated for protection against water and oil. Ideal for use in harsh environments. The LED and buzzer make the operational status clear.

Kōwae Whakahono pahi

Build the remote I/O system that meets your needs, along with compatible FC6A I/O modules.

Nga Whakawhiti Itarangi Ahumahi

Unmanaged Ethernet switches with diverse applications. Robust design and impressive versatility.

PLC

• MicroSmart Plus for control over larger machines or entire small-scale production lines.
• Microsmart All-in-One for high performance and usability.

FAQ

Q: Can the touchscreen be used with gloves?

A: The touchscreen may not work with gloves thicker than 1.5mm, depending on the material of the gloves and the environment.

Q: Me pehea taku horoi i te mata karaihe?

A: Use wipes soaked in alcohol or disinfectant to clean the tempered glass surface. Avoid using abrasive cleaners that may scratch the glass.

Q: He aha te awhe pāmahana whakahaere o te hua?

A: The product has a wide range of operating temperatures, making it suitable for diverse applications.

Tuhinga / Rauemi

IDEC HG1J PCAP Touchscreen Operator Interface [pdf] Aratohu Kaiwhakamahi HG1J, HG2J, HG1J PCAP Touchscreen Operator Interface, HG1J PCAP, Touchscreen Operator Interface, Operator Interface, Interface

Tohutoro

• Pukapuka Kaiwhakamahi