IDC205 Akoranga Tohuwhenua Tohutohu Awhina

If your ID205 smartwatch is not vibrating or showing notifications for calls and messages, please check the following settings in the TinoPit app and on your phone:

• Enable App Alerts: Open the VeryFitPro app, go to the Pūrere page, and ensure that Waea matohi a Matohi SNS (for messages) are both turned ON. For messages, you must also select the specific apps (like WhatsApp, Facebook, or SMS) you want to receive notifications from.
• Tirohia te Hononga Nihokikorangi: Ensure your watch is paired directly through the VeryFitPro app and not just your phone's Bluetooth settings. The watch must stay within 0.5 meters during pairing and within 10 meters for regular use.
• Phone Permissions: Ensure the VeryFitPro app has permission to access your notifications, contacts, and calls in your smartphone's system settings. On iOS, ensure "Share System Notifications" is enabled in the Bluetooth settings for the ID205 device.
• Aratau Kaua e Rararo: Check if the watch or your phone is in "Do Not Disturb" mode, which silences all vibrations and alerts.
• Taumata Pūhiko: If the battery is below 15%, the watch enters a power-saving mode where some functions may not operate. Charge the watch to see if functionality returns.
• App Background Running: Ensure the VeryFitPro app is allowed to run in the background on your phone so it can push data to the watch.

If these steps do not work, try unbinding the watch from the app and re-pairing it.

Note: The user's original comment was in Dutch: "Heb hem, en is een super watch! Alleen iemand een idee waarom mijn trilfunctie het niet doet als ik een berichtje krijg? Oproep komt ook niet binnen..."

When your Willful ID205 smartwatch vibrates and displays a number like 1000 (or more commonly 10,000), it indicates that you have reached a daily activity goal. Based on the manual and the VeryFitPro app functionality, this is most likely your Whāinga Hipanga.

By default, many fitness trackers set a daily target. You can verify or change this goal by following these steps in the app:

• Whakatuwheratia te TinoPit taupānga i runga i to waea atamai.
• Haere ki te Kaiwhakamahi or Profile wahanga.
• Rapua Goal Settings or Tautuhinga Whainga.
• Here you can see if your step goal is set to 1000 (or another number) and adjust it to your preference.

The vibration and on-screen animation are designed to celebrate your achievement for the day.

Based on the manual for the Willful ID205, there are two primary reasons your watch might vibrate and show a specific number or icon:

• Goal Achievement: The most common reason for a vibration and a specific number appearing (often 10,000 for steps) is that you have reached your daily activity goal. If the screen shows "10.00" it may be a truncated display of a 10,000-step goal or a specific distance goal (like 10.00 km) you set in the TinoPit taupānga.
• Alarms or Reminders: The watch vibrates for alarms, sedentary alerts, or health reminders. If you have an alarm set for 10:00 AM, the watch will vibrate and display the time.

To verify what this notification is, open the TinoPit app on your smartphone, go to the Pūrere page, and check your Matohi Whakaoho settings or your Mahi goals. If the vibration happens while you are walking, it is almost certainly a goal completion notification.

The Willful ID205 smartwatch typically comes with a kotahi tau te raihana kore raruraru. To initiate a warranty claim or seek support for a device that has stopped working, you can try the following contact methods based on the manufacturer details for the ID205 series:

• Tautoko Īmēra: The developer of the associated VeryFitPro app and manufacturer of the hardware (Shenzhen DO Intelligent Technology) can be reached at itserver@idoocn.com or chunling509223@gmail.com.
• Tautoko Waea: You may attempt to contact their support line at +86 136 4094 6524.
• Retailer Contact: Since Willful products are often sold through third-party platforms like Amazon, it is highly recommended to log into your account where you purchased the item and use the "Contact Seller" or "Get Product Support" button on your order page.

When contacting them, be sure to provide your order number, the date of purchase, and a description of the issue to expedite the process.

To turn on your Willful ID205 smartwatch, press and hold the right button. If the watch does not respond, please try the following troubleshooting steps:

• Tirohia te Pūhiko: The watch may have run out of power. Connect it to the charging cradle. Ensure the pins on the cradle align with the gold contacts on the back of the watch. You should feel a vibration if it is connected correctly.
• Verify Charging Requirements: Use a DC USB port (5V-500mA). A full charge typically takes 2-3 hours. Note that if the battery level is below 15%, the watch enters a battery-saving mode where it may appear unresponsive until charged.
• Takina mo nga arai tinana: Ensure the charging contacts on the back of the watch are clean and free of sweat or debris, as this can prevent the device from receiving power.
• Disclose Uncertainty: If the watch still does not turn on after a full 3-hour charge, the battery or internal hardware may have failed. The manual indicates a one-year warranty for defects; you may need to contact the manufacturer for a replacement.

The Willful ID205 (using the VeryFitPro app) does not currently support a specific "250 steps per hour" reminder with a 10-minute warning. However, it does feature a Whakamaumahara noho (Sedentary Alert) that can help you stay active.

To enable the Sedentary Reminder:

1. Whakatuwheratia te Mahinga VeryFitPro i runga i to waea atamai.
2. Haere ki te Pūrere wharangi.
3. Patohia Matohi Nohonoho.
4. Takahurihia te whakawhiti ki Whakahohe.
5. Whakaritea te remind interval (e.g., 60 minutes) and the time range during which you want the alerts to be active.

When enabled, the watch will vibrate to remind you to get up and move if you have been inactive for the duration of your set interval. While it does not track a specific step count for that hour or provide a 10-minute warning, it is the primary tool available for preventing prolonged sitting.

To change your Willful ID205 to military (24-hour) time, you must use the TinoPit app on your smartphone, as this setting cannot be changed directly on the watch itself. Follow these steps:

1. Whakatuwheratia te TinoPit app on your phone and ensure your watch is connected/synced.
2. Patohia te Kaiwhakamahi or Ko taku tab at the bottom of the screen.
3. Haere ki Tautuhinga Pūnaha.
4. Rapua Hōputu Wā (or Unit Settings).
5. Tīpakohia 24h to enable military time.
6. Sync your watch with the app to apply the changes.

If you do not see the option under System Settings, check the Pūrere page and look for "More" or "Device Settings" to find the time format toggle.

To resolve sleep tracking and time synchronization issues on your ID205L, please follow these steps:

• Aroturuki Moe: The watch automatically tracks sleep based on movement and heart rate. Ensure you are wearing the watch correctly: it should be snug (but not tight) and positioned about one finger's width below your wrist bone. If it is too loose, the sensors cannot accurately detect your sleep state.
• Tukutahi Wā: The watch relies on a constant Bluetooth connection with the TinoPit app to maintain the correct time. If the time is drifting, it means the app is being closed by your phone's battery management system.
• Fixing the Sync (Samsung S9): On your Samsung S9, go to Settings > Apps > VeryFitPro > Battery and ensure it is set to 'Unrestricted' or 'Allow background activity'. This prevents Android from killing the app, allowing it to sync the time automatically without you having to refresh it manually.
• Data Refresh: To see your sleep data, open the VeryFitPro app and swipe down on the main 'Home' page to trigger a manual data sync. Note that sleep data usually requires several hours of consistent wear during the night to generate a report.

The red exclamation point with error code -05 on the ID205L (VeryFitPro-based) smartwatch typically indicates a data synchronization or firmware initialization error, often occurring when the watch's memory is full or the sports mode fails to start correctly.

To resolve this, please try the following steps:

• Tukutahi me te Taupānga: Whakatuwheratia te TinoPit app on your smartphone and pull down on the main screen to force a full data synchronization. This often clears temporary errors.
• Tirohia te Taumata Pūhiko: Ensure your watch has more than 15% charge. The manual states that when the battery is low, the watch enters a restricted mode where certain functions cannot operate.
• Tīmata anō i te Mataaratanga: If the screen is responsive, go to the watch Tautuhinga me te rapu mo te Tīmata anō option. If it is frozen, try long-pressing the right-side button.
• Unbind and Rebind: If the error persists, go to the "Device" page in the VeryFitPro app, select Korekore, then restart both your phone's Bluetooth and the watch. Afterward, use the app to Pūrere herea ano. Note: This may reset the data currently on the watch.
• Whakahoutanga Firmware: Check the "Device" page in the app for any available firmware updates, as these often contain fixes for known system bugs.

If the red exclamation point remains after a full charge and re-pairing, the device may have a hardware sensor fault requiring replacement under its one-year warranty.

Note: The manual mentions that unbinding the device will reset the watch information, which is often necessary to clear persistent error codes.

分析

The Willful ID205 (using the VeryFitPro app) tracks sleep automatically, but it requires specific conditions to record data correctly. Please try the following steps to resolve the issue:

• Tirohia te Pai: Ensure the watch is worn snugly on your wrist. If it is too loose, the sensors may lose contact with your skin, preventing sleep detection.
• Tukutahi me te Taupānga: Whakatuwheratia te TinoPit app on your smartphone and swipe down on the home screen to manually synchronize data. Sleep data often does not appear on the app until a successful sync occurs after you wake up.
• Taumata Pūhiko: Ensure the watch has more than 15% battery. When the battery is low, the watch enters a power-saving mode that may disable certain tracking functions.
• Wā kakahu: The watch typically needs to detect a period of inactivity and a consistent heart rate to trigger sleep mode. Ensure you are wearing it at least 10-15 minutes before actually falling asleep.
• Hononga Taupānga: Verify that the watch is still "Bound" in the VeryFitPro app under the "Device" page. If the connection is lost, data cannot be transferred to your phone.

If these steps do not work, try restarting your smartphone's Bluetooth or unbinding and re-pairing the watch within the app (note: unbinding may clear unsynced data).

It appears your ID205L smartwatch is experiencing a software or hardware malfunction following a deep battery discharge. Based on the manual and common troubleshooting for this model, please try the following steps:

• Check Battery Save Mode: The manual notes that when the battery is below 15%, the watch enters a restricted mode. Ensure the watch is fully charged (2-3 hours) until the screen indicates 100% before attempting to use it.
• Force a Restart: Since you mentioned rebooting via the app was unsuccessful, try a hardware restart. Press and hold the paatene matau for several seconds to see if the device will power cycle.
• Unbind and Re-pair: Whakatuwheratia te TinoPit app, go to the "Device" page, and select "Unbind". This will reset the watch's information. Afterward, restart your phone's Bluetooth and attempt to "Bind Device" again.
• Whakapaipai i nga Hoapapa: Ensure the gold contacts on the back of the watch and the pins on the charging cradle are clean and free of debris, as poor power delivery can sometimes cause erratic behavior.

If the watch continues to flick between functions and drains within 24 hours despite these steps, the battery or internal sensor may have been damaged by the deep discharge. Since the product typically comes with a pūtāhui kotahi tau, you should contact the manufacturer or the seller for a replacement if the device remains unusable.

If your Willful ID205 is not recording sleep data, please check the following troubleshooting steps based on the manual and app requirements:

• Kia tika te mau i te mataaratanga: Ensure the watch is worn snugly (but not too tight) on your wrist while sleeping. It should be positioned about one finger's width below the wrist bone to allow the sensors to detect movement and heart rate accurately.
• Tukutahi me te Taupānga: Whakatuwheratia te TinoPit app on your smartphone and swipe down on the home screen to manually trigger a data synchronization. Sleep data often requires a successful sync to appear in the app's history.
• Tirohia nga Taumata Pūhiko: The manual notes that if the battery falls below 15%, the watch enters a power-saving mode which may disable certain tracking functions. Ensure your watch is sufficiently charged.
• Manatokohia te Hononga Taupānga: Ensure your watch is still paired within the VeryFitPro app (under the "Device" page) and not just through your phone's Bluetooth settings.
• Restart and Reset: If the issue persists, try restarting your smartphone's Bluetooth. As a last resort, you can unbind and re-bind the watch in the app, but be aware this will clear the current data on the watch.

Note: The watch automatically tracks sleep duration (Deep, Light, and Wake-sleep) based on movement and heart rate patterns during your typical rest periods.

E ai ki nga IDC205 Akoranga Tohuwhenua Tohutohu Awhina, the manufacturer offers a kotahi tau te raihana kore raruraru on their devices. Since your watch band connector has broken, you should follow these steps:

• Whakapā Tautoko: The manual explicitly states: "If any parts of your product require replacement for any reason, including normal wear and tear or breakage, please contact us."
• Check Your Retailer: Since Willful products are often sold through third-party platforms like Amazon, you should first check your order history to contact the specific seller or use the "Get Product Support" option.
• Kerēme Pūtāhui: When contacting them, mention that the device is within its one-year warranty period and provide details about the broken band connection point.

Please note that if the plastic lug on the watch body itself has snapped (rather than just the removable strap), this is typically considered a hardware defect covered under the warranty terms mentioned in the manual.

The time on the Willful ID205 smartwatch is not set manually on the device itself. Instead, it automatically synchronizes with your smartphone once it is paired via the TinoPit taupānga.

To set or correct the time, follow these steps:

1. Tikiake i te Taupānga: Tāutahia te TinoPit taupānga mai i te Apple App Store, i te Toa Play Google ranei.
2. Whakahohe Nihokikorangi: Ensure Bluetooth is turned on in your smartphone settings.
3. Tauhoa te Pūrere: Open the VeryFitPro app, go to the Pūrere whārangi, ka kowhiri Pūrere herea. Kōwhiri ID205 mai i te rarangi o nga taputapu kua kitea.
4. Raraunga Tukutahi: Once the watch is connected to the app, the time and date will automatically update to match your phone.

If the time becomes inaccurate over time, simply open the app and perform a manual sync by pulling down on the app's home screen while the watch is connected.

The time on your Willful ID205 smartwatch is not set manually on the watch itself. Instead, it automatically synchronizes with your smartphone's time when the two devices are paired and synced via the TinoPit taupānga.

To update the time for daylight savings, follow these steps:

• Whakaritea Nihokikorangi kua whakahohea i runga i to waea atamai.
• Whakatuwheratia te TinoPit taupānga i runga i to waea.
• Haere ki te "Device" wharangi.
• Swipe down on the app's home screen or device page to trigger a manual synchronization.
• Once the sync is complete, the watch will automatically update to match the current time displayed on your phone.

If the time does not update, try unbinding and re-binding the watch within the app, or restart your phone's Bluetooth to refresh the connection.

Note: The watch must be within 0.5 meters of your phone during the pairing/syncing process for the best results.

If your Willful ID205 smartwatch has stopped recharging, please try the following troubleshooting steps to rule out connection issues:

• Horoia nga Hoapā: Use a soft cloth or a cotton swab with a small amount of rubbing alcohol to clean the gold contacts on the back of the watch and the pins on the charging cradle. Debris or sweat can prevent a proper connection.
• Tirohia te Puna Hiko: Ensure you are using a DC USB port (5V-500mA). Try plugging the cable into a different USB port on a computer or a UL-certified wall charger.
• Manatokohia te Tirohanga: Ensure the pins on the charging cradle are perfectly aligned with the gold contacts. You should hear a click when the watch is correctly seated in the cradle.
• Tirohia mēnā he wiri: If installed correctly, the watch should vibrate when charging begins.

Mōhiohio Pūtāhui:
According to the manual, this device comes with a kotahi tau te raihana kore raruraru covering defects. Since your device failed after five months, it should still be covered. You are advised to contact the manufacturer or the seller where you purchased the device (such as Amazon support or the email provided in the app support: itserver@idoocn.com) to initiate a warranty claim or replacement.

Note: The manual specifies that the battery is non-user replaceable; attempting to disassemble the device yourself will void the warranty.

Ka taea e koe view your burned calories directly on the watch or within the companion app. Here are the specific methods:

• On the Watch Home Screen: From the main clock face, tap the screen to cycle through your daily stats. It will switch between steps, distance, and calories burned.
• Daily Stats View: From the home clock screen, swipe up to see your daily activity summary, which includes calorie data.
• I roto i te App: Whakatuwheratia te TinoPit app on your smartphone. Once the watch synchronizes, you can view detailed calorie stats and historical trends on the main dashboard.
• I te wa korikori: If you are in a specific sports mode, you can swipe the screen left or right to flip through real-time exercise data, including calories burned during that session.

Note: Ensure your watch is synced with the VeryFitPro app to keep your calorie data updated and saved for long-term tracking.

It sounds like your watch and phone are paired at a system level but the app-to-device communication is being blocked. Please try the following steps to resolve the sync issue:

• Check App Permissions: Me whakarite te TinoPit app has all permissions enabled on your phone, especially Location Services (GPS) and Bluetooth. On many smartphones, the app cannot sync data if Location Services are turned off.
• Verify Connection Method: The manual emphasizes that you must pair the watch inside the VeryFitPro app, not through your phone's system Bluetooth settings. If you see "ID205" in your phone's Bluetooth list, "Forget" or "Unpair" it there first, then go into the app and use the "Bind Device" function.
• Phone Icon Status: The phone icon on the watch indicating the function is "turned off" usually refers to Call/Message Notifications or Mana Waiata. To enable these, go to the "Device" page in the VeryFitPro app and ensure "Call Alert," "SNS Alert," and "Music Control" are toggled to ON.
• Force Sync: Open the VeryFitPro app and swipe down on the main home page (the "Mainpage" tab) to trigger a manual data synchronization.
• Restart Both Devices: Turn your phone's Bluetooth off and back on. If the issue persists, restart your smartphone and long-press the right button on your watch to ensure it is fully active.

If the watch indicates it is bound but data (like steps or sleep) still doesn't appear in the app, try clearing the app cache in your phone settings or reinstalling the VeryFitPro app.

To delete messages on the Willful ID205 smartwatch, you typically swipe down from the home screen to view your notifications. While the manual indicates that the watch displays message content and vibrates for alerts, it does not explicitly detail a 'tick' button for deletion. If you are pressing a checkmark icon and nothing is happening, please try the following steps:

• Clearkui Katoa: Scroll to the very bottom of your message list. There is usually a 'Clear All' or trash bin icon located at the end of the notifications list that will remove all messages at once.
• Individual Deletion: Try swiping left or right on a specific message to see if a delete option appears, as some firmware versions use gestures rather than buttons.
• Tīmataria anō te Pūrere: If the screen is unresponsive to the 'tick' button, go to Tautuhinga on the watch and select Tīmata anō to clear any temporary software glitches.
• Tukutahi Taupānga: Ensure your watch is synced with the TinoPit app. Sometimes clearing notifications on your smartphone's notification shade will automatically clear them from the watch.

If the 'tick' button is physically visible on the screen but unresponsive, ensure the screen is clean and dry, as moisture can interfere with touch sensitivity.

Ko te tohu mura on your Willful ID205 smartwatch represents kua tahuna nga calories. The number 500 appearing next to it indicates that you have burned 500 calories during your current activity or throughout the day.

Ko te haruru (vibration) you are experiencing likely indicates one of the following:

• Goal Achievement: The watch often vibrates when you reach a specific daily goal, such as a step count or a calorie target (like 500 calories).
• Whakamōhiotanga: It may be alerting you to an incoming call, text, or app notification.
• Matohi Nohonoho: If you have been sitting too long, the watch will vibrate to remind you to move.
• Pūoho: A set alarm may be going off.

You can customize these alerts and view your detailed calorie data within the TinoPit taupānga i runga i to waea atamai.